Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hello,
I have been having issues with two different DK:s. I am doing bootloader development and suddenly the kits go unresponsive.
nrfjprog returns the following error...
Hi everyone. For our product, we need to accomplish tests for CE certification, in accordance with regulations EN300328 paragraph 5.4.10. How can we set the softdevice s310...
I try to integrate the ble peripheral uart example and the beaconing mesh example. It build completed. But when i build and debug on nrf52 board. I have some errors about...
Hello, im a beginner in circuit design, and currently i am developing ESB device that should work on batteries.
Device simply represents a nRF24L01+ module, an ATmega48...
Hi,
I am using nordic nrf52832 nRF5_SDK_14.2.0, I use the RTT for debug, I want MCU in low power mode,so I add the following code:
while(1)
{
NRF_POWER->SYSTEMOFF...
There are parallel 8 bits input to nrf52832 GPIO pins,I want to read the data from the pins and writ it to a RAM.how to do read the data in one CPU clock?
As per this document ....
nrf5_SDK_for_Mesh_v1.0.1_src/doc/introduction/mesh_hw_resources.md
The mesh stack uses flash to store the following states:
- Encryption keys...
We modified the ble_app_beacon example to advertise the beacon once a second.
#define NON_CONNECTABLE_ADV_INTERVAL MSEC_TO_UNITS(1000, UNIT_0_625_MS)
As a result of...
Hello all.
Sorry for the nube question, but I am really struggling to try and get my IMU data from my MPU9250, to send constant notifications through BLE using the NRF8001...
When using BLE_GATTS_VLOC_USER I would tend to make the variable pointed to by ble_gatts_attr_t.p_value volatile to reflect the situation that the value can be changed by...
Hello,
I am new to nrf5 mesh. I have setup my system based on Nordic's documentation and was evaluating Serial Example with Interactive Py script.
My setup consists of...
Hi:
I have a project which nrf51822 exchange some data with TI cc2541.There is a serious issue that the nrf51822 is occasionally reset by the watchdog when it communiates...
Hello all
I am trying to get out some debug messages from my custom Firmware (and board) but the log looks like this:
<info> µ“°8$Mø@ñ¨ó¹)F¨: NRF_LOG initialized
...
Hi,
can you please to provide a more information regard power up sequence?
for example:
we would like to use DC2DC (instead LDO) with CR2032 battery.
the PCB have...
