According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Although I have already seen this discussion ( https://devzone.nordicsemi.com/f/nordic-q-a/35183/no-idea-how-to-get-manufacturer-specific-data-in-central-side-from-advertising...
Hello,
I have an nRF52840 chip ( Holyiot nRF52840 module ) and I want to program the chip using an nRF52840 DK. The Holyiot module is basically an nRF52840 mounted on a...
I am having trouble turning on bonds for DFU.
First of all, before I describe this pain, can I choose to avoid this battle by just allowing unbonded devices to DFU? e.g...
Hello!
I just bought the Beacon Kit and i was following the user guide v1.1 and I have some questions about how to use DFU. I have already downloaded nRF Toolbox app.
...
Hi,
I am using fatfs of nRF5_SDK_15.0.0_a53641a. I am writing a program with keil.
I want to know how to write the value obtained from the sensor to the SD card. ...
I am using proximity profile in sdk15 with softdevice 6.0.0 . I added flash write, writing continuously some data to flash. But it working sometimes only.
Hello,
at the moment my application is accepting more than one device if its not connected to anything. But I want that the application only connects to one device and...
Hello, i am using NRF52840 board with SDK 15.2. I am trying to read data from an advertising packet and i was just wondering if anybody on here had a good parser i could potentially...
Is it possible replace HRS to UART service (like ble_app_uart) on BLE LE Secure Connections multirole example project?
Any suggestion to easy to modify it?
Hello,
I am trying to get CLI working over UART and simultaneously use RTT for logging. I don't quite get my head around this. My platform is the nRF52840 DK. I am using...
Hi everyone,
I'm developping on nRF52840 with SDK 15.0.0 and Softdevice S140 v6.0.0
I'm using Peer Manager for pairing and bonding.
Everything work fine with io_caps...
The only examples I've found have been for ordinary single ended measurements at lower resolution, and even that is a crazy number of lines of code. Surely by now there is...
Dear nordic,
I want to change advertising data(manufacturer data including company identifier) before i start advertising
i choose central and peripheral example(because...
When I use the uart to transparently transmit, there is no problem at around 4k/s. When I increase the transparent transmission rate, there will be NRF_ERROR_SVC_HANDLER_MISSING...
