Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
My setup:
* nRF52 DK
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit.
I am struggling to properly use FDS module. I am using multiperipheral...
Hi Support Team,
By testing SDK15.0.0/Serial DFU, I find that if we use non-default baud rate(115200), such as 9600 or 38400, we have to assign a non-zero value to -prn...
Hi everyone,
I have 2 boards that I've been using for testing. One is the NRF52 DK with the nrf52832 and the other is a simple custom board i made with an nrf52810.
I...
Hi all,
I'm currently making Mbed OS 5 able to work with the NRF51 with DFU enabled. It seems Mbed OS 5 currently has no support for a Nordic bootloader for the NRF51. Mbed...
Hi Guys,
I'm using SDK 15 Version and Nrf52832 DK.
now i want to use second uart when one uart is communicating with the PC Via CLI.
How Can i make it???
Thanks in...
Hello everybody,
I use NRF52832, sdk14.2, s132 softdevice. When I install SDK examples(for example nRF5_SDK_14.2.0_17b948a\examples\ble_central\ble_app_uart_c), the minimum...
Hello , we are in the production phase, I use us addess mac(If I bought unique MAC address from IEEE. ) so our factory asks for the registry that will be configured, so is...
I want to add the UART peripheral code to the Mesh Light Switch example in latest MESH SDK v2.0.1 .
I have tried to add all the UART code to the Mesh Light Switch Client...
I'm trying to get acquainted with the NRFX_GPIOTE driver by writing a program to do the following:
initialize TIMER to generate three compare events:
channel0 compare...
Hi,
Working on a product with a couple to sensors with i2c communication. Are normally able read values from the sensors, but sometimes the i2c bus seem to be down. No more...
Hi,
I used sdk11 and sd130 at a 51822 project, it is required to be paired with a key for both andriod and ios, everything is fine but the dfu on andriod, I used nrfconnect...
SDK 14.2.
Application Timer Library
I had a question regarding the Application Timer library and the way it checks for timeout handlers. In the documentation, it says...
Hi, I have problem with nRF51822. I've bought cheap China miniboard with this chip. I can program some examples (precompiled HEXes) with J-LINK and they works correct, but...
Hi,
I want to make a program in order to assing functions to the buttons and manipulate movile phone apps without making any app or configuration into the phone.
What...