I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I have 4 button and the app_button use gpiote module, button works OK. But nrf51822 only has 4 gpiote, so what should I do if I want to use pin interrupt for g_sensor?
This question is related to https://devzone.nordicsemi.com/f/nordic-q-a/24860/sdk14-static-service-structures
Typically in your SDK examples you put global variables for...
I am trying to build the micro-ecc library following the procedure detailed in the BLE LE Secure Connections multirole example . I am using SDK v11.
I have cloned the micro...
Hi,
I have modified the nus service and added two new characteristics called txs and rxs which support read and write protection.
on the peripheral i have set BLE_GAP_CONN_SEC_MODE_SET_LESC_ENC_WITH_MITM...
Hello:
According to the website, please nrf52832 circuit design, without adding other peripherals, just as a radio Beacon, button battery voltage at 2.3 V nrf52832 cannot...
Hello, I am using SDK 15 & Softdevice 6, I am using NRF52840.
I have merged the USB CDC into a multi-link example. I confirmed that it worked, and the project was successful...
Hi
Is the DCDC enabled or disabled by default when using the DTM example in SDK v15.0.0? We can't find any reference to it so we assume it is disabled, but just wanted...
Hi guys,
On my application, I ported the code from TWI_scanner example (SDK14) and it is connected to a temperature sensor the which is read every 45 seconds, It is working...
As far as I can tell, Shockburst isn't officially supported on the nRF52840 in SDK 15. However, I have seen some success from others with this configuration, but after making...
Hi,
I have been working with the NRF52832, and trying to capture raw ADC data with the help of TWI bus. I have imported the necessary libraries (i'll attach the code below...
I have used aes_all_cli example to test computation time for AEAD EAX/GCM/CCM. I have shortened the plain text to 16 bytes, added pin toggling on encryption function enter...
I don’t have a lot of information as I’ve been totally unsuccessful in debugging this.
In short, we have a SPI peripheral that was working under SDK 14.2. Under 15.0 we...
Hi,
I am trying the connect MIO Fuse heart rate band. It follows the standard specified by Bluetooth SIG i.e Heart rate profile UUID is 180D and the heart rate measurement...
I'm currently woking on doing my own DFU system, the system should work this way : the central gets a new version of the app via the internet network and it should update...
