Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Iam working on nRF51822, i have developed my projected by editing ble_uart example project. Iam using Softdevice 110 and SDK 10.0.0. When i try to perform more then 7 BLE...
Hi, I am building a system using Nordic NRF52832 as a node. I would like to save some data (such as node ID) to board's memory so that the application can read these data...
Hello, i am developer for nrf51822, Please, have you tried to connect bluetooth nrf51822 with samsung s8 plus ?? because I noticed that sometimes it connects and disconnects...
I want to use the MPU9250 driver found in the Thingy SDK in my nRF52 project. I am using GCC 7.2 Arm/Eclipse as the development environment. The driver source file inv_mpu_dmp_motion_driver...
I would like to implement feature that swaps advertising data only if GAP address in scan request matches one of the application layer ,,authorized'' addresses.
The only...
Hi,
My app was written on Windows PC/MSVC and is ported to nRF52/Keil.
In many places I've used MSVC assert() macro in the following manners:
assert(function(arg1...
Hi all,
On SDK 15.0, Immediate Alert Service is not working without a secured BLE link. When peripheral is not paired, this latter doesn't receive any alert from central...
I’m using SDK 15.0.0. and softdevice 6.0.0.
When I compile the example:
https://github.com/haakonsh/MMD
I get the compiler error:
fatal error: compiler_abstraction...
Hi,
I tried ble_app_uart example by using SES it works fine. Then I tried it by using eclipse with OpenOCD and a STlink V2 on the debug in port I succeeded to flash it....
Hey guys,
With the new SDK15, I find myself looking at dependency problems over and over again. Right now, I am trying to setup a simple A/D conversion using nrfx_adc. Found...
Hi Env: keil uvision 5 and SDK 9 and custome breakoutboard for nRF51822 (PTR5518: no external crystal) and no SD.
I am trying doing the first steps in twi over nRF51822...
I been reading over your entire tutorials, but I have yet to see any tutorials that guides me towards creating an NRF52 project from scratch? Could anyone guide me through...
Hi,
I am transferring my nrf52832 project to nrf52810,and I have deploy the project according to the user guide (Transferring the project to nRF52810 hardware),
when I...
Hello everyone,
I'm developing an application for boards with NRF52832, Softdevice S132 3.00 and SDK 12.3.0.
The network architecture consists of:
one peripheral board...
I'm using my accelerometer's GPIO interrupt to wake up the MPU from PowerOFF mode and it works great. Now, I'm trying to use the same interrupts to wake it up from Sleep mode...
