Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
With nRFgo Studio, I define the services in the nRF8001: I create the pipes I need, and so on...
Is there any way to increase the number of credits (i.e. the number of...
Hi
Where do I find a measurement report from Nordic which shows the average current consumption for a typical BLE application (1 seconds advertising period e.g.)?
Until...
I a writing my own interrupt and DMA based code for sending commands and getting events from the nRF8001. The 8001 creates an event for every command, but if you want to clock...
Hi ,
i read tha the default profile for BLE is GATT but in the BLE_templete GAP is used. How can i interpret this? Which Profile i have to use when i wannt support for...
Hi!
My idea of sending a packet would be:
-regulary send a packet with fixed length (stated in static length field) to a base: i.e send the temperature =>4byte
-if...
Hi,
I use the nRF51822 on the PCA10001 and nRF6310/PCA10005 boards. I modified the radio_tx_example and wanted to read the actual state of the radio. Therefore I used a...
Hi
Could I modify HID report descriptor length over 255 bytes? In Desktop1.2.2.293, the returned descriptor size is only decided by wLength LSB byte and ignores MSB byte...
Hi,
I am trying to figure out how I can advertise with a custom UUID...
I know I have to start by adding a base address and then build on top of it. However, when I try...
I have a system that uses 5-byte addresses. The first 4 bytes are always the same, but the last byte has 4 different values. For test purpose I want to listen, from another...
Title says it all. My nordicsemi.com id/pw is not working here. (But it isn't working there either. I'm getting the following error, which I presume is some breakage in the...
I have a customer that wants to be able to have a single nRF51822 sends sensor information to two iphones at the same time. Is this possible? Can you pair a peripheral to...
Hello,
I have a question....
I have real ECG device and I almost got PCA10001 development board. Studying about PCA10001 I noticed that this board has ADC. I downloaded...
