hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hey,
I found that sdk 12.3.0 (the latest for nrf51822) has example fpu_fft with linked CMSIS_DSP lib, but this lib is for cortex m4. I downloaded arm_cortexM0l_math.lib...
I have a problem getting fstorage to work with BLE in SDK 14.2.0.
The fstorage example works fine until i change
NRF_SDH_BLE_PERIPHERAL_LINK_COUNT to more than 0
In...
Im am running a nrf528322 board with the s332 softdevice using sdk14.2.
I have implemented flash storage in my program according to the nordic flash_fds example. This works...
Hi Nordic,
I am using SDK 12.3.0 and S130 2.0.1. I have some questions about AFH.
1. Do Nordic stack keep track of some bad channels during communication and would skip...
Hi I am working on pcb design for a long range application with nRF52832. There are lc circuit which is implemented to antenna pins on reference design of nrf52832. I decided...
Hello,
I am trying to develop a custom BLE service. I have been following this tutorial .
I have also looked at this answer to understand the signal path for a WRITE event...
Hi!
I'm using SDK13 (Softdevice version 4.0.2) and I noticed that during an update via DFU bootloader the update of the Softdevice doesn't work.
After the transmission...
Hi Everyone
I have been trying to use nrf52840 on a custom PCB . So far everything is working perfectly except only one single issue which is the controller gets reset and...
I'm new to the NRF series, and for that matter Keil. I have a BT832A which is apparently an NRF52810.
I am able to flash my own code using Keil and and control GPIOs to...
Hello, I am battling with weird problem for 2 days already, need little help if possible, I have tried all remedies and nothing worked so far.
Here is what happened, I followed...
Hello,
I am using SDK5 for my code that builds successfully under Linux, but not under windows.
The error occurs in the SDK, not in the application. I am wondering what...
Hi,
We are trying to optimize the speed at which we send data over BLE UART with the nrf52832. Currently, we are using the ble_nus_data_send() function in a while loop with...
Hi, I am a beginner at this and I want to make a scroll wheel that connect to Android devices as an HID device. I have a custom BLE board from Skylabs (SKB569) with NRF52832...
I'm having trouble using the NRFX SPIM driver on the NRF52810 w/ Softdevice (S112). (SDK15.0.0)
I'm able to initialize but when I go to use nrfx_spim_xfer without the callback...
