Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi dear Support Team, we are from the University Albstadt-Sigmaringen in the South of Germany from the laboratory for building automation.
We have here some Nordic Thingy...
Would like to know how quickly the nRF51822 evaluation board wakes-up, after receiving an external hardware interrupt. Speifically, how fast can the evaluation begin making...
Hi!
nRF52832, SDK15, S132.
I try to use DFU. I already implemented same DFU on a SDK13. All works correct.
When flash SD132 and merged firmware with bootloader_setting...
I am currently trying to improve my positioning algorithm with nRF52832. Using a Nordic BLE sniffer, I found that having RSSI data per advertising channel would help. In short...
We've been having issues getting DFU to complete consistently with Android devices when using a two-step DFU package (BL+SD and App). Some devices seem to have far less trouble...
Hi there,
We have the application running on STM32 and we talk to connectivity chip ( nrf 52810) using serialization.
Now, I have to save bonding information on my STM32...
Hi there,
I've got something usual happening with the App Timers in my application, hopeing for some advice on how to track this one down.
There is one part in my code...
On powering up the nRF52840 I start the twis slave. The nRF52840 works as expected.
I install one i2c slave address on the system, external master has no issues communicating...
Hello,
I am using NRF52832, SDK v15.1.0.
For entering into various power down modes, does calling corresponding functions is enough to make entry into these modes or...
Hello !
In my project I have 3 phones, witch connects to one nRF8001(not at the same time).
First, phone connected, bonded and bond of this phone saves in EEPROM of avr...
I am upgrading our Nordic / BTLE library to the new sdk, which gains us ble 5.
The previous library (based on sdk 11.?.?) made light use of pstorage which, as far as I can...
I want to set up nrf24le1 in register retention mode with analog comparator wake up. The moment it wakes up it should do few ADC conversions and then again go back to sleep...
I have built up most of the support structure using the existing ble_app_uart example from SDKv15.0.0 and am now ready to port the code to our existing devices.
I'm having...
My environment is:
Windows 7
JLink Plus v9.3
IAR EWARM 8.30.1
SDK 15.0.0
Softdevice S132 from SDK 15.0.0
My hardware is a custom board with a Rigaldo BMD300...
