Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
nRF52810 board will not start on its own. It needs the RTT Viewer to be connected, then it will start and run. It has run on its own before with this configuration:
CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC...
I thought I had been extremely careful to _not_ brick the device, but apparently I did.
I created a firmware-dfu.zip file, even with appropriate keys, etc. as below.
...
We're developing a low-power application on the nRF9160 where we need the device to stay connected to the server over LTE, so we cannot enter System OFF mode. Instead, we...
Hello,
I am developing a product using the nRF54L15 and have noticed a discrepancy in the documentation regarding clock pins. My intention is to use pins 1.02 (SDA) & 1...
Describe Need to repeat disconnect/connect cycle after BT timeout. Problem is when using UART over BT with Nus Shell when connection is terminated by timeout (for example...
How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
Hi, It's looks like I bricked my Thingy:91x . It was working fine when I program it with the target " thingy91x/nrf9151/ns " then later while learning I try program the in...
Hello,
I've got some questions regarding the use of DFU target library. I get my update data from the UART and like to use a setup with two partitions on my device. Is this...
Hello, I am new to android development. I am building an Ble App for some of my work in which I want to include Direct Firmware Upgrade(DFU) over-the-air.
I have building...
Previously, I designed a PCB for the nRF52832 chip using the RFANT3216120A5T antenna ( link ). However, I was only able to achieve a very limited Bluetooth range of around...
Hi Nordic teams :
I find that datasheet v0.8 (page12) shows that SDA do not need clock.
Page 277 still shows that SDA need clock pin.
Could you help to clarify which...
Hi, I previously wrote about an unexpected behaviour which I've made a diagram for below. It's relatively simple though, the COMP watches a voltage and fires a toggle event...
Hi,
1.How to modify the transmission power of the example direct_test_mode to 4dBm? 2. Please provide Method 1 and modify it using the CONFIG configuration? 3. Please provide...
Hi,
the nrf54L15 datasheet states on SPIM "CSN and DCX are not present in all configuration" (p.559). But I can't find the information, when CSN is available.
