Hello,
Is the nrf54 family's I2C peripheral compatible with I3C? I need to communicate with several I3C sensors on the same bus.
If yes, is the software support only...
I'm using the nRF Connect SDK on nrf5340dk and encountering issues when trying to use the non-blocking (asynchronous) I2C API.
i am particularly getting this error - ENOSYS...
Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I'm trying to load ble_app_hrs_c on the nrf51dk and im getting the error
"error: L6047U: The size of this image (34328 bytes) exceeds the maximum allowed for this version...
Hi,
I am trying to receive BLE advertisements on Ch38 (=2426MHz) without using SoftDevice, i.e. with direct register access. However "EVENTS_DISABLED" is very rarely called...
Nrf52832 based on sdk14.2 development as a slave, when linked with the iPhone, pairing and binding, and then get ancs service; and Android phone connection, direct communication...
I am working on a project working with remote connectable beacons. One of the easiest ways to save power in these applications is to reduce advertising speed, however, this...
Can anyone give me a tip on porting the code below, which works great in sdk12, to sdk14? I'm using the nrf52832 and the ble_app_hids_keyboard example and need to get a real...
Hi, I'm kind of a newbie, haven't had much experience with embedded outside of arduinos etc.
So I started to look at this: https://learn.sparkfun.com/tutorials/nrf52832...
for sdk15.0, SES,
is the twi_scanner example known to work with nrf52810?
getting errors,
undefined reference to nrfx_twim_init, nrfx_twim_enable, nrfx_twim_xfer
Hi,
I am studying the GPIOTE example from SDK 14. I did some modification adding other led and doing the leds blinking in differents times (LED1 blink each 1 sec and LED2...
Hi,
The nRF52832 does not support Long Range and i was wondering if the use of "RADIO_MODE_NRF_250KBIT" would increase the range. My application is a mesh network.
Do...
Hello Everyone,
I am using nrf51822 with S130.
Currently I am using arduino following this repo to program nrf51822 and its working fine. However, I want to shift to keil...
Hi there
For test purposes, I first implemented a simple serial reading & parsing function in polling mode of a gps device (sending @ 1 Hz).
Everything works fine when...
Hello,
i am evaluating the nRF52840 on the nRF52840-Preview-DK. I have connected an ADC to the devkit via SPI and my code reads data from the ADC via GPIOTE, PPI and SPIM...
We've got two SPI slaves that we need to talk to with the 52840 (PCA10056 dev kit for now) using SPI Manager. In the initialization of these devices, I'd like to use nrf_spi_mngr_perform...
when I use flash to storage my data,I call the fds_record_write(&record_desc, &record) ,and it return success,but my machine run err, my ble broadcast is missed.I used the...
I'm trying to understand what is meant in section 5 of the BLE on Android primer: "The peripheral device should disconnect itself when it gets disconnected by the client....
