We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Has anyone modified the spi_master_using_nrf_spi_master example (or otherwise gotten) the Crystalfontz CFA211TFH 128x64 panel running w/o mods on the nRF52 DK? I have a panel...
Hello,
I captured following data using a Bluetooth dongle for WIN 7 and a Bluetooth keyboard . I also used Wireshark with USBCap driver to capture data going from BT Keyboard...
With my sparkfun 52832 board, when I use the __WFI instruction and I set my device to generate interrupts on P04, the code returns when an interrupt is generated. With the...
We created a custom made board with an nRF52832 and an LIS2DH accelerometer. The board is working fine when it is being powered from a power supply with 3V but when it is...
Developed with SDK 15.0.0. and s132_nrf52_6.0.0_softdevice
After I generate the DFU package, and upload it with nRF Toolbox, it will returns " Upload failed: REMOTE DFU...
SDK 15.0.0, s132_nrf52_6.0.0_softdevice
I have followed the instruction below:
https://devzone.nordicsemi.com/f/nordic-q-a/29067/installing-micro-ecc-issue/115222#115222...
Hello,
Nrf52832 ibeacon broadcast signal is unstable, and the rssi deviation of left and right upper and lower signals before and after the detection of the same distance...
Hello,
I'm working on some LED sequences using the NRFX PWM driver and I can't get the durations I want right.
Let's say that I want a semi-blinking LED (100% - 50% -...
HI
platform:
sdk:15.0.0
52840
\nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10040_uart_debug
I want encode(uart) dfu packet not by nrfutil:
(nrfutil...
In my design, I am using a module based on the NRF52832, with a specified LF clock accuracy of +/-250ppm. In my application, I am using v15.0.0 of the SDK with SoftDevice...
hello, we would like to know which development environment Nordic Semi supports/recommends for NRF52832-QFAA-R (except GCC) Is there a special offer from a manufacturer (e...
I'm in the process of scoping out a new project that is in the realm of robotics. It involves one wireless controller that a person would use to turn and drive four wireless...
Hi there,
I have found a similar thread that dates back from a year ago ( https://devzone.nordicsemi.com/f/nordic-q-a/29073/altering-qspi-address-mode ) but I would like...
I created a application that sometimes uses the BLE for 10 seconds. To turn on the BLE I'm using the function
and to turn off the BLE I'm using the function
I already...
Hello!
I'm trying to interface the DHT11 with my DK. I'm coming from Arduino where all I had to do is to drop some library and instantiate an object. Here with the nRF52...
