Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
WIth the upgrade to the new SDK, registering the callback handlers has been made more difficult to figure out.
The .sdh_ble_observers, .sdh_soc_observersers sections are...
Dear Sirs!
On one from 25 boards there is offset in ADC input about 30 ADC units. Vref = 0.6 V, Gain=6, 12 Bit ADC, oversampling 256 sample.
In other devices I do not...
Hi, Could you send me a sample to send "Hello World!" string from sender task to receiver task?
I am using C:\Nordic_Semi\nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral...
Hi, I have a question regarding the behaviour of a button in the nRF App in Android, sometimes the button "READ STATE" in the "Generic On Off Server" configuration changes...
Hi,
I have managed to run DFU mesh example and successfully updated firmware of whole mesh network. Now i am looking for options to perform customized DFU over mesh . Lets...
We are experiencing issues with nrfutil being flagged as containing malware, see screenshot below. Has Nordic experienced this before, is there something we can do to stop...
Hi
I have reported this before and now that you are a quarter away from a fully featured mesh sdk can I ask you to please enhance the SDK so that you supply a function that...
I'm evaluating possibilities of BLE-LESC Pairing/Bonding with the ble_app_hrs peripheral on the nRF52840-DK with SDK 12.3 and SoftDevice s132. To see what's going on in the...
Is it possible to flash multiple custom boards using sagger DKs at the same time?, assume 2 custom boards and 2 DKs, would they be able to flash the custom boards in parallel...
There are many places in the file fsm.c that have this compile condition check
#if defined FSM_DEBUG
blabla
#endif
that is wrong. The compiler will ignore it. There...
Dear Nordic,
Hello, I have to configure 2 UART. I have saw this post .
however, I have made a demo version for the project without 2 UART function, so I hope to apply...
Hello, I´m trying to compile the BLE Heart Rate service projects using SEGGER Embedded Studio. After importing the project from nrf52 SDK, I tried building the project but...
Hello,
I want to implement home automation project using 3 nRF52840 dongles. i.e I want to connect all the 3 dongles with each other and the signal sent from one device...
Hello, I am trying to design a product based on BLE MESH. I would need gateway to be able to accumulate data from network and send it outside. I need that gateway to connect...
