I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
We have an application where we have a large number of sensors, some relay nodes and one or more gateways. The sensors and relay nodes are provisioned by the gateways and...
Hi, I can normally log with NRF_LOG_INFO(). But if i enable softdevice (bluetooth stack init) logging stops working. Interesting part is that there are several log lines before...
BLE Control by Main CPU (MCU):
1. How the MCU communicates with BLE HW?
2. What is the amount of MCU performance is required to control the BLE? (expected answer example...
Hi nordic.
I use SDK 14.20 and nrf52840 board and s332 softdevice.
Our app has to use ant+ and ble.
My device connect with app.
App requests device to ant+ scanning...
hi guys:
When I was using mesh sdk, there was an error in compiling.
I use examples\light_switch\server\light_switch_server_nrf52832_xxAA_s132_6_0_0.emProject
I am...
Hi,
I am using SDK 14.2 -> BLE peripheral proximity example. I was trying to add a custom service and some characteristics to this proximity example. I basically took the...
Hi, I have two strange problems regarding the NRF_LOG. 1. In a for loop, char string that has changed is not printed out as what it contains now, it is printed out as what...
Hi,
i have purchased the following module
However, after connecting the VCC and GND to 3.3v DC supply the module is not detected. My questions are :-
Does...
how to slove it
1> Linking light_switch_proxy_server_nrf52832_xxAA_s132_6.0.0.elf 1> build/light_switch_proxy_server_nrf52832_xxAA_s132_6.0.0_Debug/obj/ses_nrf52840_Vectors...
I am using the nRF52832.
I want to go to sleep in absolute lowest power mode possible that still allows a timer for wakeup. Using LFINT.
I don't need ram retension, etc...
Code example: nRF5_SDK_15.2.0_9412b96\examples\peripheral\usbd_ble_uart_freertos
Board: custom board with nRF52840
What are the fastest and easiest steps to make this...
Hello,
I am trying to code nRF52840- DK with MAX30003 ECG Board Using SPI. I have referred Arduino Uno Code for MAX30003 ECG.
I need some help for Driver Development if...
Hi,
Is there a way to dynamically disable only the fork of a PPI channel or should I go through disable-free-alloc-assign sequence?
Will nrfx_ppi_channel_fork_assign...
