Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi,
nrf5_SDK_for_Mesh_v2.0.0_src
When complete provision a provisionee , provisioner will assign provisionee a mesh key and device key.
Now i want to know how to calculate...
I can get a clean build and working product with some workarounds, but a couple issues remain from migrating sdk 13.1 to sdk 15.0 (SES nrf52832 s132).
1) After nrf_drv to...
Hi,everyone.
I had learn for below Links and compiling is no error.
https://devzone.nordicsemi.com/f/nordic-q-a/26448/nrf52832-maximum-number-of-central-links/104063#104063...
Hi,
I'm having problems to run the Loopback example in the Bluetooth Mesh SDK:
infocenter.nordicsemi.com/index.jsp
I'm receiving a timeout.
My setup is as follows...
This is a duplicate of https://devzone.nordicsemi.com/f/nordic-q-a/35127/spi-master-0-uses-300ua-upon-first-transfer but I wanted to be safe because I pre-maturely verified...
Hi,
I have been working on MPU9250 examples given in here .Though the program runs fine in KeilUvision 5, the output in tera term shows only 0,0,0 for Accelerometer values...
Normally one writes 0 to an event register to reset it.
I am writing a uart driver and when I open my interface I want to prime my transmit pump by setting EVENT_ENDTX to...
Hi all,
What are the default preflashed contents in the out of box nrf52840 flash?
I assume that bootloader is not present. If my assumption is correct how preflashed...
I'm looking at the SDK15 I2S example project using DMA. My dev set up is 52840/Keil.
The project is under: \nRF5_SDK_15.0.0_a53641a\examples\peripheral\i2s
In the callback...
I am new to BLE development, if that helps preface this question.
My goal is to get a BL652 module by Laird working with the BLE UART example from the Nordic SDK. I am using...
We are working on porting an MESH example from Segger to IAR.
We started with the BLE Peripheral Template, and pulled all the code for the light_switch_provisioner into...
Hi, I noticed that Silicon Labs announced their Mobile Mesh application for Android and showed a demo video .
I searched Nordic's GitHub page. However, I couldn't find...
While trying to make a custom server model, based on the on-off model in the documentation, the code breaks when receiving an incoming message. The problem is in the file...
Hi ,
We have designed an Nrf52832 customized board having 32mhz crystal but not having any low frequency clock. The board is working fine with the blinky and other codes...
