I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I'm using a nRF51822 on a custom board. I would like to implement serial DFU on it using the bootloader_secure example.
1.) Is serial dfu implemented in sdk 12.3 ...
Hi all , I am beginning with MESH SDK on Window . I use NRF52832 board with Softdevice S132v3.0 on KeilC5 . I read instructed at infocenter.nordicsemi.com/index.jsp but I...
Hello Nordic:
I am trying to add advertising with whitelist function to my code which is base on
nrf52832 dk
softdevice s332 5.0.0
SDK 14.2
I use the example code...
Dear Nordic support,
In our company we are using application "nRF Connect", in android platform. It works well, however when we try to use it on iOs platform the application...
Hello!
What version|tag|commit of MQTTSNGateway ( https://github.com/eclipse/paho.mqtt-sn.embedded-c ) do you use in Raspberry Pi image? Do you use special way to build...
I had the nrf52832 with BLE 4.2 running just fine with iOS 10.xx and Android phones.
iPhone would SCAN and connect and I could interact with the services on the hardware...
How to select nrf528332 UART clock source, how to make the serial port baud rate not change with temperature?When the baud rate is 9,600, the baud rate varies greatly with...
Hi,
I found this in the documentation for the Timer Library of the SDK 14.
' When app_timer_start() or app_timer_stop() are called, the timer operation is only queued...
I plan to use the flash device driver from Nordic (52840) in a Zephyr system. My plan is to use the <flash.h> api but it seams that this api is not available in a default...
Hello!
I'm trying to read data off of a commercial blood pressure monitor (Qardio arm) using an nrf51822 with the nrf51 SDK v10.0.0 as the central role (s120). I am able...
I am unable to build any example project of nrf sdk for mesh. I have added the SDK root in my global macros as : SDK_ROOT=C:\Nordic_Semi\nRF5_SDK_15.0.0_a53641a . And still...
I run the below code on nRF52DK and measure the power consumption of the chip (using nRF current measurement jumpers). The current consumption is 0.47 mA which is a lot just...
Hi,
I am using nRF52832 board. I want to connect serial mesh example with 'ble_app_uart' . I try to use the same method http://infocenter.nordicsemi.com/index.jsp?topic...
Hello,
I have 8 12-bit ADCs that produce 3300 samples per second, which I will send over a Bluetooth link, so I need a data rate of about 320 kbits/s. I was thinking of...
