Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi
Can you please provide an example/pseudo-code on how the channel_mask member in the ble_gap_adv_params_t struct is used? The only examples provided in the SDK and the...
I have open a brand new nRF52 Development Kit. It is not recognise by the nRFgo Studio. I have tried the trick you mention on this thread:
https://devzone.nordicsemi.com...
I have been looking into the ble UART example a bunch trying to incorporate it into the ble blinky example.
I keep getting an NRF_ERROR_INVALID_STATE error when calling...
Where can a person get decent documentation on developing for BLE on the nrf52840 using segger embedded studio?
Is it possible to create a new project without having to...
/cfs-file/__key/support-attachments/beef5d1b77644c448dabff31668f3a47-cfe0b78c5edc467ca49b481632af4156/pair.c
I'm attempting to do LESC OOB pairing with another transfer...
Hi Team, Could you please let us know the worst case current consumption of nRF52832 at -40 and +85DegC.
Below are the current consumption values taken from datasheet: ...
Hello,
I am using sdk 12.2.2 and nrf52 customised board. Now my challenge is as follows.
When I am adding this in my code.
nrf_gpio_cfg_output(26); nrf_gpio_pin_write...
Hi all,
I use nRF52832 with the UART peripheral example.
I try to enable connection event extension in the device and get an error.
I use SDK V15.0.0 and Softdevice...
I've been trying to find a way to program a hex file onto the dongle via the command line on linux.
I would very much prefer not having to touch the mouse in order to program...
Hi, I was hoping someone could tell me if/when a version of the nRF Mesh Android App found here:
https://www.nordicsemi.com/eng/Products/Nordic-mobile-Apps/nRF-Mesh
Will...
Hi,
I'm using NRF52840 sdk v15 with Softdevice.
I have multiple SPIM instances and I make sure they are never active at the same time.
Can I share the pins (except the...
Hi, I'm trying to rate nrf52832 with stack ble_app_uart softdevice. My IDE is the IAR workbench for ARM 7.80.4. I downloaded the latest version nRF 5_SDK_15.0.0_a53641a, which...
