Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello everyone,
In my current application , I am using nRF52832, with the SDK 11.0. I have a problem with the BLE connectivity, which I think is a hardware issue.
With...
I am doing a connectionless system where I am just broadcasting the data. I am showing a loss of about 50% on the receiver missing the data packets. I have tried before to...
Hello,
I configured pin P1.15 as output and with GPIO_PIN_CNF_DRIVE_H0H1 but I only get 1.7V ?
Does "standard drive" means that the pins can't get to 3V ?
Thank...
My project is based on the Thread cloud coap client example. I would like to know if my CoAP POSTs to the cloud are successful.
I added a "post_response_handler" to the...
Hi,
I've been trying to read/write data from/to the internal flash storage of my nRF52 development board.
I am using SDK11 and softdevice s132
I have modified the flashwrite...
Hi,
I've been trying to read/write data from/to the internal flash storage after a ble disconnect event occurs on my nRF52 development board.
I am using SDK11 and softdevice...
Hello,
i'm developing an interface based on nrf52. The app does a direct connection, performs some exchanges with the peripheral, and tells the peripheral to disconnect...
Hello we have a more stable external reference voltage source than the VBG for the ADC we want to use.
The voltage itself is higher than the allowed reference voltage specified...
Hi,
i am working on a project that in it i had developed a firmware for nrf51844 based on soft device 130 v2.0.1, now i decided to move the project on nrf52840 . i had read...
Hi! I did see a post about this, but is there a way to implement any kind of throttling/flow control over the Nordic UART service?
About the only thing I can imagine is...
Hi,
how can I publish a message to unicast address from a generic on/off client with mesh sdk?
How can I set the address?
Jost to be more precise, the function:...
After installing the USB driver for the nRF52840 dongle and using it successfully, and then connecting the nRF52832 DK it fails with "error occurred when opening port. Errcode...
Hi everyone,
I was trying to use QSPI interface with the on board external flash memory MX25R6435F on nrf52840 PDK
This is what i have observed, Inside the linker tab...
Hi, I have nRF51822 Board
Can I make it as a beacon kit?
what changes do I need to do to change that as a Beacon? any Source and Instructions are very helpful for me....
We need our PCB assembler to be able to program nrf51822 modules in situ. We have tracked the PCB to include a tag-connect footprint to this end. The assembly house will purchase...
