I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hi, I have 2 questions regarding Nrf52840's zigbee connectivity.
1. Is it compatible with ALL other chip manufacturers, or at least, what about TI? CC2530? Zigbee has...
Dear all,
I am testing the light_switch demo (SDK for Mesh v2.0.1 and softdevice 6.0.0) below the following configuration:
-- One client: nrf52-PCA10040 DK (light_switch_client_nrf52832_xxAA_s132...
I read in a CMakeList.txt, that EXPERIMENTAL_INSTABURST_ENABLED is posible on the nRF52832 platform only.
Is it possible to get Instaburst running on a nRF52840 chip using...
I would like to separate the BLE communication from the main.c and place it to a separate file. I followed the example of the default ble_app_template as well as nordic's...
Hello,
Configure the nRF52832 (PCA10040) as suggested in the link below:
github.com/.../Android-Image-Transfer-Demo
Launched the Android Image Transfer Demo and we were...
Hi, i am working on a message model based on the simple_on_off model. I am able to send and receive a buffer via unicast or multicast. Now i am trying to develop a reliable...
I need help to build a demo of product consisting of BLE observer. I chose the nRF51822 due to lower cost, many choices for modules, and it does just what I need. I was able...
Hello System: Windows 10 Pro 64bit, 1703 I prepare the Toolchain on Win10 for BLE Mesh 2.0.1 SDK. During compilation of "pc-nrfutil-mesh_dfu" i get the error "missing NETAPI32...
Hi Nordic team
I compile the example ble_app_interactive in keil ver.5.24.
And the below error message occur.
I have compiled other examples and it works fine. (except...
Hi
I am designing Circuit with nRF4122 - QFN package 48 pin, as per datasheet there is circuit for Trace/ PCB Antenna
But i am planning to use Chip Antenna and BAL-NRF02D3...
Hi,
I have a custom board someone designed with two SPI masters and one I2C master. We're now trying to enable the second SPI master and I'm running into errors because...
Hi all,
I am working on FOTA, my set up is with SDK15. I have followed the steps for DFU and i have used the secure_bootloader example, the thing is working fine, i can...
hi i have attached my gps+gsm module with nrf51 development kit and while reading an out put i wont be able to see any output , even with out put i dont know to to do debugging...
Hi,
I have completed all steps in the example at the following link https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader and all...
