I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
Hi,
I am new to NRF development. I am using 2 nrf52840 DK one as central and other as peripheral(for reference). I am using ble_gap_gatts example from central side. i...
Hello,
I am using NRF52840 development board with SDK 15.2. I am using the template peripheral project since i want to get comfortable with the peripherals on the board...
Hi All,
I am working on customized board using nRF52840 chip, I have a application which was developed using nRF development kit that communicates to my customize board...
I'm trying to follow the SDK 15.2.0, nRF52832 development board, BLE Secure DFU bootloader example. I cannot seem to get beyond exception error running nrfutil to download...
Hi
I am using ATM90E36A IC from microchip for which Microchip gives ATMEL studio library.
Is it possible to compile the library in Nordic SDK 15 and use the functions...
Hi, Great Nordic support team:
Our client Is wondering if there's a way could sense the level of a GPIO configured output?
I mean, sensing the level without config the...
I am trying to do just bonding when I receive the BLE_GAP_EVT_SEC_PARAMS_REQUEST event as described in the sequence chart in this link infocenter.nordicsemi.com/index.jsp...
Hi
I have a problem with long latency on interrupts and long delay on retriggered interrupt.
I have a nRF52832 running with external HFCLK source. Using the SDK 14.2.0...
Hi, Im trying to add multiple endpoint support to a zigbee project.
Im using the SDK for Zigbee 2.0 but in the documentation says:
" APIs for multiple endpoints A single...
Hi,
If you are using NRF52840, I am using SDK14.2 and Softdevice 5.0.0-2 version.
I want to update to SDK15.1, Softdevice 6.0.0 via USB bootloader DFU. Is it possible...
Dear All,
1. I'd like to know if below two lines which high-lighted in RED , Line width should be designed to provide 50 Ω impedance matching characteristics ?
...
About the data rate item of 5.4 Receiver Opetation in the data sheet of nRF24L01 +. Sensitibity is -82 dBm at 2 Mbps and -94 dBm at 250 kbps, is 250 kbps more susceptible...
Hi all.
I have a working multi-link central NUS project, and a working USB_CDC project for the nRF52840 SDK 15, nordic dev board.
I have merged the two as I need a USB...
Hi
I have a RGB LED and want to have bellow process for brightness:
Red from o to 100 then Green from 0 to 100 and Blue from 0 to 100.
till now i by bellow code i can...
Good afternoon,
I am currently using ble_app_hrs_rscs_relay example in the ble_central_and_peripherals part of the SDK. I am just testing out the example and trying to pair...