Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi,
I am developing nRF52832 peripheral, SDK15.
Let me know about whitelisting.
I'd like to below functions.
1. Delete item(device) in white list.
2. Changeing...
Configuration is all 12 combinations of the following 3 x channels, 2 x modulations, and 2 x bit rates were tested to find the worst case. More substantial testing was to...
when i upload the hex file of a s132 softdevice example program through nRFgo studio,
its shows hex file uploading failed and shows this message "Invalid SoftDevice, data...
Hello Everyone,
I am facing an issue when trying to connect back BLE central again after disconnecting it from the BLE peripheral once.
The issue is reproducible as follows...
If I want to send two byte, how can I do? I use the https://github.com/NordicSemiconductor/Android-nRF-Blinky sample code.
In BlinkyManage.jave
public void send(final...
hi All!
I'm trying to use new SD140-6 function sd_ble_gap_adv_set_configure() , according to spec. if last PARAM is NULL, function behavior : " When this function is used...
Hello, there was a strange problem in the mass production of my product. The previous batch of problems was less, about 0.5%. The later batch is quite serious, 45 of 500 products...
Hej,
on trying to update firmware on nrf52832 over the air I'm getting the error message INSUFFICIENT_RESOURCES.
Actually I don't understand the error message because...
I want to put the BLE program to the firmware of another STM chip and load the program via the I2C to the nrf52832. Will it work? If yes, is there any tutorial or example...
Hello,
I'm using nRF5 SDK with version 15 and nRF52832 IC. I want to sample some data with 3200Hz sampling rate. I can set the timer minimum 1ms Which means 1000Hz. How...
I want to write at the end of memory ROM data in address 0x7FFFF
uint8_t tst_arr[1] = {6};
sd_flash_write((uint32_t*)0x7FFFF, (uint32_t*) &tst_arr, 1);
Is it correct...
Hello ,
System configuration
Set up 1 Adafruit BLE Feather running stock central UART example from NORDIC SDK version 15.0`examples connected to host PC using USB
Set...
The dedicated NFC pins on the nRF52840 are P0.09 and P0.10. However, these are noted as "Standard drive, low frequency I/O only " pins, with "l ow frequency I/O" defined as...
Hi, I'm facing an issue after provisioning the Client and Servers from Light Switch example of Mesh SDK 2.0.1, using the Android App. Provisioning is successful, however,...
Hello,
Following on from this question , I've been trying to identify the source of unexpectedly high power consumption when using the RTC. In order to test this, I am using...
