Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hi, i am learning with thingy 91 x and nrf9151dk. I made the online courses and succesfully conect to the cloud with the nrf desktop quick start in both devices. Now, i would...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Today i received my brand new 2 pieces of nrf51-dks. when i wanted to try out some of the examples, i tried to copy over the .hex file to the usb drive, but for some reason...
Dear experts
We have no experience using Nordic SOC neither Nordic SDK, but want to start the contact with the platform.
Our aim is to get knowledge, setup the development...
Hi,
Can I use the serial interface to interact with an nRF52840 dongle running a mesh stack?
If so is this limited to UART or can the USB connectivity be used?
If any...
Hi,
I am developing a device based on NRF52840 soc in ble central mode. Could I claim when I do not call sd_ble_gap_scan_start function BLE radio is thoroughly OFF and there...
Hi everyone,
Maybe this is a very simple question but I want to avoid future troubles, that's why I'm asking. I want to copy an example from SDK16 and rename it. For example...
My Win 10 is up to date. Seger' J-Link driver is OK. Here's message from log screen: Please help to find what I missed. Thanks.
08:03:35.048
Using nrfjprog library 10...
Hello,
I am currently trying to use the MQTT publisher example to send a message to a locally hosted MQTT broker (I assume I can use a local IPv6 address?). The MQTT broker...
Hey Nordic Team,
I'm in the midst of integration the nRF91. As with the nRF52 designs, less work was taken out of the RF design aspect because it has a built in balun. As...
Hi Nordic：
I burned the AP & Modem firmware in the picture below, and found that the current consumption when entering PSM is 500μA. Please help to analyze. What caused...
Hello ,
I am using freertos with nrf uart service, i could able to get these timings that seem little bit weird.
one of the pin toggled for each successful ble_nus_data_send...
Hi Nordic ,
I have a nRF52840 project development based on SDK 15.3 . Now ,I need to add DFU feature there. we suppose to use background DFU here. we will use long range...
We have been using RSSI as a signal for doing location services, however we are find that a bit challenging. From reading the literature in the field, several researchers...
Dear community,
for my upcomming project I would like to use the nRF52832. Since there also exists a development kit I started to make myself familiar with Embedded Studio...
I have two nrf52 chips connected to each other via SPI
I send data from my Nordic Uart app to my nrf52 chip 1 and I want to send the data that I receive from Mobile app...
