Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I am unable to set the PA/LNA Mode on NRF52832 using SDK 14.2 ( Soft Device Version S132 5.0 ) using the Fansttel BT832X SoC.
i have used the exact function on the below...
There is the nRF52840 specifications sheet at the reference circuitry there is a pin 74 that is indicated as ground, what is this? 74 does not seem to line up with the method...
I don't know if this something I'm doing wrong, a Segger stupidity, or something else. I'm using SES and copied the examples/ble_central/ble_app_blink_c project to another...
I am struggling with excess current consupmtion using uart+fifo. It seems like ~300uA is drawn by UART and disabling via app_uart_close() doesn't help.
I have checked all...
HI,
I have nRF9160 modem DK. I am working a project based on http sample.
The LTE is initialized through the call:
w_lte_lc_init_and_connect();
But after ( in the...
Hi, In my current project I'm implementing an ANT Shared Channel topology, where in each channel period the master polls a slave with an acknowledge message and receives the...
Hello,
I can connect to LTE with the iBasis SIM that came with the nRF9160DK but have been unable to connect with any other SIM. Here is what happens in the LTE Link Monitor...
Hello,
I'm currently developing on a Adafruit nrf52840 express. I'm working under the impression I need to develop the code in C in order to use my code in mass production...
hi, i just purchased nrf52840 dongle, still new to use nordic components.
i have no idea on to use it as a beacon. already done the part in SES.
i want to make the dongle...
Hi Experts,
I have looked into the Mesh SDK for several days, i found one question is the device how to handle the same message they transmitted before after power reset...
To the kind attention of Nordic support team,
I have been doing the pairing between two devices using nrf gazell secured library. Then, what I want to do, it is to read...
Hi,
We plan to measure the sleep current of the *whole* Thingy 91 system including nRF9160, nRF52840 and sensors. Do you have a firmware (sample app or similar) that puts...
To the kind attention of Nordic support team,
I'm evaluating your standard gzp example (proprietary_rf/gzll/gzp_dynamic_pairing, sdk15.3). From what I see, the device to...
Hi,
It seems that the nRF52811 for the most part draws less current the nRF52832. For example:
nRF52811: 1.4 μA at 3 V in System ON mode, no RAM retention, wake on RTC...
