I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I am developing for an nRF52810 target application.
I am using IAR 8.42 with a PE Micro debugger. If I debug a project (call it project A), the linker ROM space starts at...
Hi,
I tried the SDK_DIR\examples\dfu\secure_bootloader\pca10040_s132_ble example from nRF5_SDK_16.0.0 with my custom board with nrf52832 mcu.
I followed this guide:
...
To the kind attention of Nordic support team,
I 'm working on a custom project so that nRF52840 can operate in two different mutual exclusive running modes. A USB operational...
I'm starting a new project that ports an existing (non-Nordic) application to a system based on an nRF52840. My current solution is based on FreeRTOS, so I'm looking at the...
Hello,
We are experiencing 2 different but related app_timer failure conditions.
app_timer_create() returns NRF_ERROR_INVALID_STATE
app_timer_start() does not return...
Hello,
I am using nrf52840 microcontroller and segger embedded studio for making firmware. I made my own project and I am having trouble configuring nrf logging which i...
Hi,
i am working on a Bluetooth application with the nRF52832.
When I try to connect a Pixel 3 (Android 10) via nRF Connect app which is available on store, I am unable...
Hello!
I've got a small problem in Visual Studio Code for Windows, the intellisense can't seem to find the nordic header files from the downloaded sdk. It compiles just...
Greets,
I'm using the aws_iot library atop an nRF9160 successfully to connect and interact with AWS services.
The aws_iot_evt_handler_t callback is triggered when messages...
I'm not sure if what I am trying to do is the proper way to send ble data, and I since I can't get it to work, I'm assuming I'm doing it wrong. What I'm trying to do is send...
Hello, I wanted to send data over peripheral device to the central device by using ble UART example. I used ble_nus_data_send() function in main(void) function. I have checked...
Hi, New user here, I develop using Kicad and it has an antenna based on the Ti SWRA117D design, which is 2.4GHz. Can I confirm I only need two components (as per reference...
Hello,
I am using the SPIM module to communicate the NRF52832 with a sensor, every time it generates an interrupt - which is generated with a frequency of 25Hz. For the...
Hi expert,
I'm working for my project that make a controller for drone, and that i need nus for as my service so i can exchange the data (send order via rx from smartphone...
Hi I'm trying to integrate the iBeacon and Eddystone protocol together. For this I'm using the timeslot to advertise the packets simultaneously. I have successfully integrated...
