Do I have to use external host MCU for nRF51422? What can the ARM Cortex processor inside SoC 51422 do and cannot do?
I want to create a mesh network with hundreds of ANT...
Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
Hi,
Looking at pstorage related code, it appears that it handles data copy from RAM to Flash.
Can I use pstorage functions to move data within Flash? I want to implement...
HI All,
We want to use UART RXTO event to detect UART packet boundary.
So we propose to add one entry APP_UART_RXTO to app_uart_evt_type_t in upstream sdk to sync.
...
I can not understand how works READY register in SPI master:
after first byte transmission READY sets high, i set READY low and send second byte, but READY never sets high...
I can upgrade the firmware by MCP on air ,But there are one conditions:
reset the device while holding down the Enter Bootloader Mode button or a invalid application is present...
Hi,
I am running (and reconfiguring) ble_app_lbs (LED + Button BLE app) example as a kind of start off project for me. I am actually trying to figure out where I can control...
Hi,
When i increase the global buffer , i got this error.
if i reduce buffer size and add few more characteristic , i am getting same error.
How can i use Flash memory...
Hi All,
I started with example ble_app_multilink_central for S120 from sdk 6.1. I then started stripping the application to get a barebones central. I removed app_trace...
What I`m using:
-nRF51422 EK
-Keil v5
-nRFGo Studio 1.17.1
-SDK 6.0 and 6.1
-SoftDevice S110 v 7.1
-Applicatio: ble_app_hrs
I first Programm the SoftDevice
Softdevice...
I've done a lot of reading on the forums about this topic and done a lot of trying myself. I haven't had much luck and it seems like most everyone is in the same boat.
...
Hi,
On my ble application, I want to keep after wake up reset the previous value of a variable, I tried using sd_power_ramon_set(0x000f000f) to keep on all ram partitions...
It seems like a pretty large hardware/software release just came out and I am a little confused. Where can we find documentation about all the new hardware (nrf51822-QFAX...
Hi I try to run master control panel on PCA10024 development boad. On master control panel, I set File->Options->Serial port: "Show all serial ports". Then master control...
Hello,
I'm reading S210_SoftDevice_Specification_v2.0.pdf and there is written: "The ANT channel encryption engine provides the ability for a single channel..." does this...
I didn't find information about size of buffer within softdevice 310 for ANT messages.
I found that S310 requires: 128kB Flash, 9kB RAM, Stack 2kB
But how big size of...
Hi, are my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS or AIN_2_3_PS will not...
