Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I'm using a relatively large GATT db that has rd_auth and wr_auth set to true for every characteristic. This prevents the stack from automatically replying with cached values...
I'm using the MAX9814 electret pre-amp's output as an input to an analog pin of the nRF51822. The MAX9814 has a 1.2V swing at 1.2V DC (so it goes from 0 to 2.4V). VDD for...
Hello,
I have some questions about the DC/DC conversion factor in nRF51822.
In the datasheet nRF51822_PS v3.1, Figure 11 shows the graph about conversion factor...
I would like to change the device name of the nRF51422 trough a mobile device(Android AND iOS ). The name should be stored even when I disconnect the supply.
From a nordic...
Sir,
We designed a prototype card including "rfd22301" containing nrf51822. We will use in mass production directly the nrf51822.
We will use the BT as a transparent UART...
Hi, I try to transmit mp3 or wave file.
and I am using nrf51822. Is it possible?
I know that people usually use the A2DP profile, When they send a music or video
...
I'm running example apps from the SDK on a PCA10028. When debugging in Keil uVision, I find that I can only stop the code once. The second time I try to stop the code I always...
Hey All,
I am working on a project that involves a Redbear Labs Blend as a sensor platform, then transmits the data to a dfrobot Bluno over nRF8001 BLE. I'm still new to...
The release notes for S110 v 8.0.0 say .
The SoftDevice Specification corresponding to this release is the
S110 SoftDevice Specification v2.0.
I can't find...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi, I am using nRF51822 to generate two channels PWM to control motors. Softdevice is V5.2.1. But I found the the Blue tooth connection sometimes dead if the PWM frequency...
I would like to create a unit which is intermitting in the master and in the slave role.It should be most of the time "advertising" and waiting for some master to connect...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
