I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hi, I use nRF52840 dk PCA10056 and keil μvision5 . In Pack Installer of keil μvision5 , PCA10056 is not displayed . So I choose nRF52 PCA10040 , is it OK ?
I'm trying to send data from an IMU at about 50Hz over BLE to a smartphone. I'm finding that after some number of successful transmissions, I start to get the NRF_ERROR_RESOURCES...
Hi
I'm using the unmodified fatfs example in SDK16 with PCA10040 dev board connected to a Mikroe SD-Click board which is nothing more than a breakout board for microSD cards...
It is possible to provision the NetKey, AppKey and unicast address of a node using the serial protocol, using the following messages:
Mesh Subnet Add, Opcode: 0x92 - NetKey...
Dear Sir or Madam,
It´s the second time, I got the same error while start developing with nrf52833 demo board. For first step, I flashed a blinky example to the board -...
Now I'm trying to change a device name in `nrf_dfu_ble.c`. I set NRF_DFU_BLE_ADV_NAME like following.
And I imported `stdio.h`, `string.h`. And I edited `gap_params_init...
Hi,
im trying to flash a 3rd party demo board (MDBT50Q-512K Module Demo Board) with nrf connect for desktop. As programmer I use original Segger j-link edu mini.
As...
Dear Nordic:
My peripheral is configured to use MTU 247.
When connected by NrfConnect of IOS, I can receive NRF_BLE_GATT_EVT_ATT_MTU_UPDATED event and check the effecitve...
We are designing in the 52840 as a processor in a new sensor product and are looking at using the HOLYIOT YJ-18010-nRF52840 part that you indicate on your site is a third...
Env setup:
nrf52840 on PCA10056, SDK 16.0.0, S140, FreeRTOS, secure bootloader
Description:
I'm trying BLE background DFU in the application.
Had reference iot/background...
Hi
Is there any implementatiaon of nrfutil, and more specifically the DFU via serial port, as a C library? My use-case is I need to update an nRF52840 from within an already...
Hi,
I am able to set up uart async receive, but when I try to set the call back using uart_callback_set() so that i can call the uart_tx() routine to push the data out,...
Hello,
I am working on nRF9160DK. I am using SES for ARM (Nordic edition).
How can I import new libraries for any project? Let's say I want to import SD card libraries...
