Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0).
I need clarification if softdevice uses RTC and if so is the Errata 20 applicable...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0)
I am looking into Erratas and working on the possible workarounds. However...
HI,ALL！
I use official routine development NRF52832，
NordicSDK\nRF52\nRF5_SDK_16\examples\ble_central_and_peripheral\experimental\ble_app_att_mtu_throughput\pca10040\s132...
Hey!
I'm using mesh sdk 4.0, nrf5-sdk 16.0 and run the serial example.
currently I successfully provision 2 light server with the ipython interface, and to configure them...
I am trying to do service discovery using the discovery manager library on any BLE device I connect to my central. I start the service with bt_gatt_dm_start(conn, NULL, &discovery_cb...
Is there any app available that can use to track lost/retransmitted packets and get some log?
I’m trying to find best position for a nRF52840 module with chip antenna without...
Hello everyone,
I work on a project with a custom board and e NRF52840 on it.
I work with the SDK15.2.0, the SoftDevice s140 and FreeRTOS.
The BLE function well but...
Hi,
We have a product in manufacture based on nRF4122, SDKv9.0.0 and using S310.
We are aware that this is nearly 5 years stable but are considering the options to upgrade...
I am currently working on a project based on the light_switch mesh example and am running into an issue where I'm receiving several of the following error throughout operation...
i am trying to customize my advertisement data, for that i am using sd_ble_gap_adv_set_configure API, and it is also returning error status 0. But the data what i am giving...
Hi
I dont know if this ever worked or stopped working after I updated SES to v4.5
The SES v.4,5 had no nrf support so I had to back down. (not sure why the update was...
Dear Sir,
To Nordic Dev kit, a sensor is interfaced via SPI lines. Using SPI in blocking mode (Polling).
After initializing SPI communication, 2 bytes are written to the...
nrf master control panel android app sent only one byte, while sending more than one byte gives Error 13 (0xd): GATT INVALID ATTR LEN
cant we send more than one byte in...
Hi,
I'm gathering assembly specifications for a custom PCB that uses nRF5340. I don't find any specific recommended reflow profile and solder paste for assembly. I stumbled...
Hi,
Bit of a newb question but I am evaluating the Thingy 91 dev board and would like to also connect some sensors via the SPI interface. I was wondering what would be the...
