Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I'm trying to capture events like accessing an invalid idx of a C++ vector
I'm using the method at , like this:
std::vector<int> my_array;
my_array.at(10000);
...
Hi,
I want to use the SAADC to measure the voltage on the VDDH pin. I am using a design based on circuit config #4 and following the SAADC example in the SDK version 15...
Hi,
I am using nRF mesh Android app version 2.1.4
I have flashed the devices with light-switch example application under nRF5 SDK for mesh V 4.0.0 on PCA10040 DK. I'm...
Hi,
I have a custom application running on a custom PCBA using the nRF52840 MCU. The Softdevice (S140, v7.0.1) is also utilised because the main application supports BLE...
Hi,
I am looking for the timing of when a connection event will happened. Radio Notification seems the right method for me since it provide an interrupt right before an...
I'm looking at the feasibility of using extended and/or periodic advertisements from an NRF52 to be received by a cell phone. I've used nRF Connect on a couple slightly older...
We have a multi protocol project THREAD and BLE. It currently uses the BLE DFU for OTA updates. We would like to add the THREAD DFU so we can use either transport mechanism...
Hi -
I have 2 questions:
1) I am looking for an example application that demonstrates acquiring acceleration data at high ODR of 5kHz from LIS3DH sensor using nRF52832...
Hi
I had got some problem with fds_record_write(). I found that I couldn't get the correct data from flash without waiting fds_evt_handler( ) that was called after calling...
Hi, I would like to test interconnection between an android phone with nRF Connect (central) and nRF52840 DK (peripherial) in long range mode. My question are:
Does it...
Hi,
I have a problem when i try a dfu on my device for the first time.
To explain, my device is flashed the first time with NRFJPROG, and i flash the SD+BOOT+APP.
So...
Hi,
I have used nRF5_SDK_15.3.0 .
I have tested secure_bootloader example code with Adafruit Feather nRF52 Bluefruit LE - nRF52832 Board . And its advertising and work...
Hi,
I have an application that uses the nrfx_saadc driver to measure voltages. One init-function that sets up the saadc and two channels, and one sample-function that calls...
