Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hello,
I'm trying to build the HTS221 sensor example for nRF9160 but got this error :
I'm compiling the code with ncs v1.2.0 and here is my prj.conf :
Can someone...
Now I can only download the 《nRF52810 product brief.pdf》 . The link is shown below:
https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF52810/GetStarted...
Hi,
I am using nRF52832 for my project. I want to perform secure connection using numeric comparison.
I want to know how six digit passkey is generated by the softdevice...
Hi,
For the testing purpose, I would like to send a few basic packets from LTE Link Monitor on nRF9160 DK to our cloud. I found a way how to do it through the nRF9160: Serial...
Hello guys,
We are developing our IoT prototype with Thingy:91 board using v1.2.0 tag.
One of the things we need to to is as follows:
Scan the BLE area looking for...
Dear Nordic
In ble_advdata.c of nRF5_SDK_16.0.0_98a08e2 , with the function:
I think parsed_name_len < strlen(p_target_name) should be parsed_name_len <= strlen(p_target_name...
After the update from the SD4.0.2 to the SD6.1.1 (nrf52832), it is not anymore possible to pair with the OnePlus5 (Android 9.0) With the Galaxy Note8 (Android 9.0) it works...
Hello,
So I assume VDD is from USB or the battery depending on whether USB is there or not. So, when the SAADC outputs ~3.258 V (in low power mode) that's fairly correct...
I need to measure with SAADC two channels in the same time (NRF_SAADC_INPUT_AIN6 and NRF_SAADC_INPUT_AIN4).
Is possible ?
Have you an code example?
Thanks
Marco
Hi,
I used a nRF51 dongle (PCA10031) wit the nRF Connect (v3.3.0) Bluetooth Low Energy application to communicate with a MBN52832 development kit. This works great until...
Hello:
I am looking for the best way to capture the SD and application error/fault(s) so that when the device is restarted, the data can be transmitted to the central...
Hi
I have installed the toolchain according to the getting started assistant, nRF Connect SDK v1.1.0
I try to load the asset tracker application in Segger with CMake_lists...
