Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi nRF team,
I am configuring my GPIO pin with below code sample.
out_config = GPIOTE_CONFIG_OUT_SIMPLE(false);
err_code = nrfx_gpiote_out_init(MEM_SPI_SS_PIN, &out_config...
in ¨¨Blinky example¨¨ we press button on one board and led get ON on other board.
I want to ask how can I modify this example or any other example
what are the functions...
Hi
I am looking for BME680 example code for Thingy91,since I donot have access to NB-IoT / LTE network as of now, i can't use the asset tracking demo code. I just need BME680...
hello
we used sdk_15.2.0 ->proprietary_rf -> esb_ptx example to check 52840 transmission.
now we have 61440 bytes need to be sent out. i used following code；
int main...
I`m searching after a document / description how to setup a user test case for BLE RF distance range measurements. Maybe Nordic have a smart phone app which we can use to...
I am evaluating NRF for a commercial project. I am also new to this BLE business so trying to learn fast.
I am trying to run the supplied BLE UART example on the NRF52DK...
I am trying to develop a low power scanner with nrf52832 which is is acting as both central and peripheral (beacon)
I need to detect other tags like itself transmitting...
Hi,
is there any example of firmware that can be used on nRF24LU1P that perform some data receiving on RF side and send them over USB?
The most important part is the USB...
Hello, We have designed a PLE peripheral based on nRF52840, SDK16.0, Softdevice v7.0.1. We have having an issue where, occasionally, we send a certain data (a command) to...
Hi everyone,
I created a custom service that I want to be advertised through scan response. Also, I want to advertise the INFORMATION SERVICE through advertising data. I...
Hi, I'm working with nRF52840 with NFC. I don't have yet the external antenna to connect to (now I'm using uFL), but I'm not sure about the trace width that goes from the...
MeshSDK: 3.2.0
StockSDK: 15.2
Hello,
I have a network where the sequence numbers have become corrupt due to removing devices from a network and then provisioning other...
Hello,
I've been trying to write my own library that uses UART.
I went through the "uart" example and wrote this piece of code.
uart.c
gpio.c
main.c
...
I would like to ask you a question, that is, the RTC in the chip of 52832, in the case of non-power-off restart, is there any way to keep the RTC time and continue the timing...
I am trying to extract the gps coordinates and use CoAP to sent the info to Telenor IoT server. I am using the gps demo code provided by Nordic .
https://github.com/NordicPlayground...
