Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, im working with the Arduino Example called pingpair ack. Sometimes I get this "Blank payload". ¿What does it means? The message was correctly recieved?
Sometimes I get...
Hi!
I'm not good at C and microcontrollers programming. Could somebody clarify, if nrf_rtc_counter_get interrupt safe? It just reads value from rtc register->COUNTER (24bit...
Hi,
When I enabled NRF_BL_DFU_ENTER_METHOD_PINRESET.
The 52840 Dongle into the DFU mode every time hardware power reset.
Use other DFU enters method does not have this...
There are so many references to this, and so many versions for each DeviceFamilyPack, but literally not one mention of how or where to install this.
Can someone help me...
Hi,
I'm using two nrf52 dev kits and the ble_app_uart & ble_app_uart_c examples to test a BLE link that would ideally be able to hit a 1Mbps throughput. I am, however, very...
I am scanning beacons data in ble central profile with gap scan parameter
static ble_gap_scan_params_t const m_scan_params = { .extended = 1, .active = 1, .interval = 0x640...
Hi,
I am using modified MQTT simple code on a DK board. I am wanting to "capture" URC's. For testing I have enabled CEREG and CESQ URC's and disabled the AT host library...
Hi,
nRF9160 DK I have a simple question regarding processing at command responses. I was hoping to extract the individual values from a at command response using the at...
Hi,
We are designing our custom board with NRF52840 , we need to add serial capabilities over USB.
We were thinking about adding FTDI Chip ( FT232H ) connected to the...
I have been using SEGGER studio 4.22 on my MacBook for a while now. Today I went to open my project and it said I didn't have a license. I chose continue and it just opens...
Hi,
I have Power Profiler Board. It works on Windows Desktop.
But no on Ubuntu Machine:
Ubuntu 16.04,
nRFConnect 3.3.0 and nRFConnect 3.3.1 AppImage
Power Profile...
Feature request.
In the current Connect SDK, I must add the name of any new 9160-based board directory to ncs\nrf\cmake\multi_image.cmake.This requires anyone installing...
I am making a simple device based on nrf5240 - I want to control the servo from a smartphone. I used the WART and Blinky examples as a starting point. The data exchange algorithm...
Not really sure where the problem is here, my guess is in the code... I just recently saw this: https://www.avrfreaks.net/comment/1342846#comment-1342846
Although my issue...
Hi!
I have written a driver for Dali (prototocol used in lighting management system) on nRF8240. It is a baremetal application which uses the SDK of Nordic (the drivers...
