HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hello!
Trying to capture and print the rssi values for all simultaneous connections from the multi_central example. I'm using an nrf52840 SoC that will be connected to four...
Hello, I am looking to use the thingy 52 as a remote sound recording device using BLE connection. I also have downloaded the source code for the thingy app and my question...
i want the ble_app_uart.c example to advertise also . so here i want to merge the ble_app_uart central +peripheral uart right ?
what are the changes i need to do
...
Hi Sir,
According to the datasheet of 52840 (v1.1), in the ref. schematic, the requirement of 32M is +/- 40 ppm.
In section 5.4.4.2, for the frequency tolerance requirement...
Hello,
Please comment on the expected difference in achievable range using 20 dBm vs. 23 dBm output power. Any details, assumptions, questions, etc. would be appreciated...
Hi, I'm looking for a more modern transceiver than nRF24L01 + and that works for the same. I am looking for a low or ultra low power transceiver that allows the implementation...
Hi, For my POC I use nrf9160 dk. Nrf52840 is used for scanning ble devices and nrf9160 dk is used for sending data to mqtt server (very similiar to one of the examples with...
Hello there!
We would like to use INT1 pin of ADX362 low power accelerometer on Thingy:91 board to interrupt nRF9160 (e.g. wake it up) when some motion is detected.
To...
Hello,
I am currently designing a new board using the nRF9160 chip and looking for an alternative component to use instead of the GPS RF Amplifier QM14501 and RF Switch...
I need to exchange data between nrf52840 and Linux PC. I see example project in nrf5SDK/examples/peripheral/usbd
Can anybody advise any example project for Linux C/C++ to...
Hi,
I'm working on nrf52840. As far as I understand, that device supports connection to peers with BLE 4.2 at least.
However, I'm able to connect via my phone, which...
Hi,
I have some questions regarding the state of the GPS functionality, and the future plans for nrf9160.
Will continuous GPS tracking while simultaneously using LTE...
Hi,
We are working with DK nrf 52840 and developing android app with nrf mesh library. is there a way to receive the feedbacks to the provisioners when any generic clients...
Hi ,
1-) Is there any dma half transfer interrupt ? if there is where it is in documents ? ( i check this link but i couldnt see anything about this https://infocenter.nordicsemi...
It is pretty straight-forward to use J-Link RTT Viewer on Windows (as described in the Debugging with Real Time Terminal tutorial ). Is there a similar viewer to use with...
