Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hi everybody, I am a beginner and I need your advice to start to modify the example of Radio Receiver/Transmitter. Ultimately my goal is to measure the time between the reception...
Error message from KEIL CMSIS D/L :
Update available for ARM::CMSIS (installed: 5.6.0, available: 5.7.0) Update available for ARM::CMSIS-Driver (installed: 2.5.0, available...
I have developed an bootloader operating with external flash for image storage. For the use case it is not acceptable to put the device into an inoperable (no-application...
Hello,
I've been looking at this post devzone.nordicsemi.com/.../ in regards to characteristic lengths.
I'm still not clear on the matter. Currently I have initialized...
Hi, I'm confused how to do fota of mcuboot on the nrf9160.
The source code is public on github in this branch: https://github.com/ExploratoryEngineering/nrf9160-telenor...
I just installed NRF Connect on an Archlinux via the AUR , but I cannot install any app. I even upgraded the package to 3.3.3, but I always get:
Error
Unable to...
Environment: nrf9160DK v0.8.2 nRF Connect SDK v1.2.0 Modem firmware: v1.2.0 Toolchain: gcc-arm-none-eabi-9-2019-q4-major-win32 I started with the nrf mqtt_simple sample and...
Hi,
I have bought TMP117 with NRF52832 from Nordic, a wristband becon module. I am new to this boards. I want to create my own Android app. I want to know how to do this...
Helllo,
i'm using a custom shield with the Thingy:52.
I need to control some TWI chips, but these chips (ADG728) have only one register.
I have done a specific driver...
In the nRF5 SDK v15.0.0 there is an example for beacon. (in my case ble_app_beacon_pca10040_s132)
This example works fine and acts as a non-connectable unidirected beacon...
Hi, I'm trying to add Characteristic User Description 0x2901 and CCCD 0x2902 to a characteristic. It seems 0x2902 always comes before 0x2901 in attribute table. Is there any...
Hello,
As per your sugesstion opened a new ticket in reference to existing ticket,
https://devzone.nordicsemi.com/f/nordic-q-a/60891/unable-to-read-the-128-bit-uuid-with...
Hi,
I'm using nrf52-pca10040 and sdk-15.3, I tested an eeprom chip following twi_scanner example, using no block nrf_drv_twi_xfer way, which works well, then I put it in...
Hello,
I followed this tutorial and github example in order to make a custom service with the characteristics I need. However, I am running into an issue where the board...
