Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
HI everyone,
I am currently facing an issue when using nrfjprog to flash my nrf52832-based custom board using nrfjprog.
Here is the steps I followed:
- Creating application...
Hi,
I have recently been evaluating the nRF52840 for the research purpose. I came across a question related to this product that I could not figure it out myself.
I noticed...
Hi Nordic
Is there any sniffer can sniffing ANT traffic?
I just trying 52840DK and nrf-sniffer-3.0, and read user guide, it seems to sniffer BLE packets only.
Regards...
Hello Supports,
I downloaded the SUPL package, and extracted it to nrf/ext/lib/bin/supl/.
For enable it in gps example, I set CONFIG_SUPL_CLIENT_LIB to y in prj.conf...
I have borrowed a snippet from github nordic repository for doing a single Vdd voltage sampling. I lifted the code and installed it directly into my app. It appears to hang...
address = 0xe7 0xe7 0xe7(3bytes),
dataLength=0x01(8bit),
S1>>PID=0x01(2bit);NO_ACK=0x00(1bit);
How to calculate CRC, I need software calculation, not hardware processing...
Hi,
Greetings!
One of our product requirement is that we have to upload SIGmesh network data (lamp status, temperature etc) to cloud server
Here we have to use SIGmesh...
Hello,
will the Systick be sourced by the LFCK when in WFI/WFE low power mode (SYSTEM ON IDLE)? On nRF52 series the freeRTOS port uses the RTC as systick for its tickless...
Hi all,
I'm developing a board based on nRF52832.
I want to implement delay power on and power off through holding a single power button for about 3 seconds.
Regarding...
I am try to make twi communication and i got strange issue.
When i use twi scanner example with unconnected pins on my board , i am not see any requests
Great oddity that...
Hello,
I am working on nRF52382 IC. I am accessing GPIO also. But still i don't get the access of antenna. I have make the circuit as per the development board of nRF52...
Hi,
What is the practical maximum throughput of nRF proprietary protocol? The following table showing ESB and GAZEL has 1.3Mbps and 128kbps respectively.
https://www.nordicsemi...
Hello,
I am developing application based on nRF52833 DK. Basically, my application scans all iBeacon messages (ADV_NONCONNETABLE) and transmit to computer.
I would like...
Dear All,
I need your help because I created a PCB with the nrf52840 and a flash connected exactly as the one on the dev-board.
The only difference is that the one on...
I am using nrf52840 . I am sending data 2 bytes as FF .I put the data in 2d array like this. char dataSend[1][5]={"FF"}; This char dataSend has 1 row and 5 length .This should...
