I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am using SDK_15.3.0. I am using Segger Embedded Studio 4.5.2. I'v tried 4.1.2 also. Every time I compile, even just with an example central project, I get the following...
I updated a working project based on nRF52832_xxAA 32Mhz crystal, from nRF5 SDK 14.2.0 to nRF5 SDK 16.0.0 now the timer is 6 times faster, the code hasn't changed is there...
Hello,
I modified the light_switch example of the Mesh SDK to transmit sensor data. Currently the Mesh is made of one client and several servers (all are nRF52840). The...
I am trying to determine if it is possible to implement a "OS native" BLE transport layer for nrfutil. That is, use the Bluetooth interface the machine and remove the need...
Hello,
I need more precisions about the software described in one of your files.
In the nAN_34.pdf Section 3.2.2 "Computer Software" ( https://infocenter.nordicsemi.com...
Hello,
We are using the nrf9160 in a custom hardware solution, with SDK v1.2.0 and modem firmware v1.1.1. There are some data items that we would like to load into NVS at...
Hi,
I've got a custom board with nrf52832 mcu. I use the nRF5_SDK_16.0.0_98a08e2 with s132_nrf52_7.0.1_softdevice.hex.
Sometimes the app_error_fault_handler is called...
Hi,
I have a project based on the NUS (Nordic Uart Service) example.
I have bought a USB dongle MDBT50Q-RX manufactured by RAYTAC ( https://www.raytac.com/product/ins...
When I tried to send data in the form of float it shows an error and I changed it to another format as sending flag, mantissa(3 bytes), and exponent (1 Byte). Can anyone help...
To the kind attention of Nordic support team,
I have got an nRF52840 working application using usb and gazell, and I'm porting it from nRF52840 to nRF52833 these days. Yes...
I have some nRF52832 devices that have been flashed with a Softdevice v13 based firmware and can receive OTA firmware updates. Unfortunately their enclosures are sealed and...
Hi,
I am attempting to get the adxl362 sample working with the nrf9160 dk board. I am using the nordic SDK v1.2.0. I cannot get it to compile, compiling the code below fails...
Hello,
I am using SDK SDK_15.3.0_59ac345 in application that receives data from UART, and the aplication is running in background just ADV.
In the main function, after...
Sir,
With reference to the subject cited above the undersign is working as Assistant Professor in CSE Department and doing R & D in IOT.
I want to recommend your product...
