Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi,
I'm using a custom nRF51822 board powered by a coin cell and need to trigger a specific LED when the battery is low.
Using this thread as the reference, I tried to...
Hi Have anyone used Rust base crypto library on nRF52-DK dev board? I've tried to use ring in my Rust project and set target to "thumbv7em-none-eabi", but I got an error below...
Hi, Looking at the Keil website I was assuming that the I could develop a nRF9160 based custom design using this IDE with ULINK2 interface. There are Nordic development packs...
Hello,I am testing the ble_app_hids_keyboard code in SDK14.1。After NRF52832 connection to the IOS device, the device's soft keyboard disappeared.I want to know how to pop...
Hello,
I am designing my second revision of custom hardware and am debating replacing my external regulator with the nrf52840's internal REG0 stage. I have read the product...
Hello Nordic DevZone team,
Please find the following setup details which we are using.
- Host side(I.mx6ull): Linux has all the kernel configurations that are enabled...
I have a simple HID BLE device which send left/right/return/home keys to a Android device.it works well when i test it on my android phone(Lenovo S5).but when i test it on...
Hi guys,
As I am new to this and wanna learn, can I know how to achieve the subject.
If possible, can you give me the exact steps to follow while achieving it.
BTW,...
On our device, we're seeing a problem when trying to run a Mesh DFU to update our firmware.
We first generated a DFU package with application version Y. Then we tried sending...
Hi,
My problem has similarities with Case 250648 (for nRF52840):
When trying to run your AT-client sample for the nRF9160 on your DK board, I cannot debug. Segger Embedded...
For a customer I am developing a Zigbee coordinator / Gateway with the nRF52840. As hardware I am using the nRF52840 Development Kit v2.0.1. As Software basis I use the “Zigbee...
Hello together, I am trying to update the nRF9160 device because I can't get a network connection. I followed the guidance of a manual of this site ( https://devzone.nordicsemi...
Hi,
just for your information:
the function nrfx_twim_xfer() prints always a warning, even if there was no transmission error. I guess NRFX_LOG_WARNING() should be logging...
I am trying to modify the https_client example from ncs\nrf\samples\nrf9160\https_client on Thingy91 so that it will retrieve an authentifcation token from AWS Cognito. So...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0).
The nRF52832 acts as SPI Slave and we want to wake up from Deepsleep when...
