I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi All,
I am trying to add custom characteristic to existing HRS profile. I am making few modifications to this profile for my custom requirement.
I am adding new characteristic...
Nordic boards come with the awesome JLINK-OB, and I'd love to use Segger RTT for app tracing, but have been not been able to get it working in Zephyr using the nRF5340-PDK...
Hello,
I checked most tickets on devzone but didn't find the answer for my issue, if you can please help me about this.
I'm using: nRF52832QFAB - SDK16 - SD132 v7.0.1...
Hi,
When upgrading the DFU with an app everythings goes seemingly fine, all init+app bytes received, validated and so on. The DFU does its resets when done updating settings...
Hi,
In our application, we need the TCP/UDP socket keeps alive even when its receiving is timeout. so we changed the process code in do_tcp_receive() and do_udp_recvfrom...
Hi. I am fairly new to all of this. I am currently researching BLE vulnerabilities for a University project. I have had great difficulty attempting to flash the Nordic BLE...
To the kind attention of Nordic support team, I have been putting to the test a scenario where three devices are used: one gzll host and two gzll devices. When devices are...
Hello
I have a project that was developed in Keil, and now I want to migrate it to Segger Embedded Studio. I have followed the tutorial in this link ( https://devzone.nordicsemi...
I'm trying to understand why this happens.
My application uses the softdevice, which configures some NRFFW registers. I program my application, bootloader, SoftDevice via...
Hi
I am using nRF connect for nRF5340 and i am in need to compile using segger embedded studio.
I tried installing segger IDE with the version 4.5 , I got the free license...
Hi,
I encounter a issue with my printed broad that mainly copy the thingy52. I download the thingyv210HW10.hex into my hardware. And then I debug the code (thingysdkv210...
Hello,
Currently, we are working on a product which leverages the following:
NRF52832 (64KB RAM and 512 KB Flash)
SDK v11.0.0
Soft Device 132
It has been reported...
Hi,
I see from the code in GitHub:
https://github.com/NordicPlayground/fw-nrfconnect-nrf/blob/master/samples/nrf9160/gps/src/supl_support.c
That the new A-GPS is using...
