I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi Now I'm developing using nRF52832, and trying to estimate programming time.
So, I want to know what time to wrie one word "tWRITE" mean exactly. Does it mean that one...
Hello, I am currently building a wireless sensor network, and I am searching for a transceiver and not a complete system on chip. I was working using NRF24L01, and now is...
I tried to write in flash since a couple of weeks.. and i am not able to do it... I am using SoftDevice... so i think i have to use Persistent Storage Manager Where can i...
Hi Devzone:
I am using the example project "fsorage" on nRF52840.
I see the project specifies the range for the flash storage to be
.start_addr = 0x3e000, .end_addr...
Hello
I am preparing for Bluetooth SIG certification. I use nRF52810 / SDK15.0.0 / S112 6.0.0.
I've been helped by Nordic about QDID before.
https://devzone.nordicsemi...
Hi there
After initializing the SoftDevice S132 V6.1.0, I request the HF crystal by calling the function sd_clock_hfclk_request():
Later in the code, after a BLE connection...
SDK:V16.0.0
chip:52832
development kit:window+keil
I trying to combine libuarte and ble_central\ble_app_multilink_central\. My project work well in ble_central. But...
Hello everyone, I need to build a photo capture application.
And the CMOS sensor go through MIPI-CSI2 interface.
Is there any example code and library for nRF5340?
Hi,
How should the USB pins be handled in case I don´t want to use them? Should they be just left unconnected?
What about VBUS pin?
Thanks and regards,
Juan
Hello,
I got the issue to run the NRF9160 DK as an external AT-Modem. What I need to do is to issue AT-Commands over the UART, which control the NRF9160 modem through an...
Hi , I am running zigbee cli example code from sdk and configuring nrf52840 board as coordinator and trying to add xbee module to zigbee network. Coordinator is not accepting...
OK, a bit of confusion somebody can clear up for me, I hope;
Does NRF_SERIAL_EVENT_RX_DATA get sent when there is ANY data in the RX buffer, or only when the RX buffer is...
Hello
I am developing peripheral interfaces on nrf9160 dk, For I2C, sPI and ADC I am not able find exapmle codes. ALso could not find api required for the same to develop...
