Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
Hi everyone,
I am working on a project with the NRF9160 DK where I want to use the UART3 channel.
The issue is that I got compiling errors when I add CONFIG_UART_3_NRF_UARTE...
Hello,
I want to test the Thingy Mesh Provisioning Demo v0.7 with the codes provided on the GitHub:
https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo...
Hi,
I am using s140 v7.0.1 for nRF52840.
I found if I configure NRF_GPIOTE->CONFIG[0], then BLE will not work.
Which GPIOTE channels are used in s140?
Thank you.
Hello,
I need example code or guidance in how to receive eddystone advetising packets on the nRF52832.
In my project, I can send standard eddystone packets to a app...
Hi All,
I am new to BLE technology and I am working on nRF52840 and I have below queries.
1) I need to operate my device to scan and advertise both at the same time when...
I stuck a breakpoint in the main loop to capture the timer values. Everything looks good, the capture has worked. The interrupt isn't called however. I've disabled the softdevice...
Please understand my low English level.
Segger cannot find be_advdata.h. I've added this route to the preprocessor. But an error occurs. How can I fix this?
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
For better clarity, I am trying to understand...
When scanning, is there a built-in way to detect and ignore duplicate advertisement packets (i.e. from the same device)? Specifically, I want to instruct the SoftDevice not...
Hi.
Thank you for your hard work.
I would like to apply the Timer example to the Uart example in SDK 15.2.0.
It was able to build without any problems before the timer...
Can somebody help me to setting up debugging in eclipse (nRF52840_xxAA)? As all I use some old tutorial here . But I still can't set up debugging on eclipse for 3 years of...
Hi
We are using the nRF9160 to drive the SD pin of the QM14501 LNA, which would typically consume 740uA. While the pin is driven high, I only measure 0.7V on the pin, so...
Hello,
I'm receiving a FDS_EVT_UPDATE (FDS_ERR_OPERATION_TIMEOUT) in my fds event handler. My update didn'it work but i don't know why.
If someone has already faced this...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
