GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hi
We are using the nRF52832 chip in a design and try to reduce the cost for the product. I have some ideas to simplify the circuits but have some questions about the capabilities...
After clicking on Raw Data in Nrf connect App I am getting this 0x0201041AFF590000150112233445566778899AABBCCDDEEFF0FFFFFFFFC3. what are 0201041AFF these bytes ? can I remove...
Hi
There is a lot of sleep mode at 5.2.1.1
Could you explain what the different between "ION_RAMON_EVENT", "ION_RAMON_POF", "ION_RAMON_GPIOTE", and "ION_RAMON_GPIOTEPORT...
Hi,
I just added some more data to my iBasis SIM card, but I can't seem to find the receipt for the purchase. Where would I find the receipt for this purchase?
Thank...
Hi there,
I have a few questions regarding the Development Kit hardware design. I just bought up the polygon pour manager. I noticed that all layers except Mid-Layer 2 are...
In the documentation, its suggested that the antenna should have a matching network between the WLCSP NRF52832 and the 50 ohm transmission line that looks like this:
...
Hi Team,
I am working on SYSTEM ON mode with Low power mode also called Idle mode in nRF9160 module.
I was able to go to Idle mode with current consumption of 6uA with...
Hello there,
I created a project a while ago with the SES and the SDK 15.x. For a new Project, we would like to move to PlatformIO. Right now I am evaluating where we will...
Hi Guys
I recently made my own PCB for a project. On the PCB I am using a Laird BL654PA Module with external antenna. All the I/O's work great but im struggling with the...
Hi,
We had met problem at buttonless DFU with bonded information at Andriod set-top-box.
The problem we saw is we can not know when the ATT table is different at andriod...
I'm trying to wait on a single POLLIN event on a net socket, but I'm finding that poll() will still return immediately with the POLLIN event even if it's not set in the struct...
Hi , I am developing a zigbee project using nrf52840 using NRF52 zigbee sdk . I had to do some changes in zboss header files ( zb_config_common.h and zb_config.h ) to change...
I'm using the NRF52840-DK with the SB40 jumper cut, then powering through P21 and measuring with an ammeter across P22. USB is unplugged during measurement. I'm using zephyr...
Hi,
Eventhough I am able to communicate with my I2C slave, this message appear for every transmision.
[00:00:00.709,350]
[1;31m<err> i2c_nrfx_twim: Error 195952641...
