Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Using LFCLK, enabling and running the WDT causes the nRF52840 to hang until the watchdog reset when calling nrf_drv_clock_lfclk_release . This is with SDK v15.2.0 Steps to...
Hi I'm using nRF52 DK to program a BM832 module where I want to run some code to manage FLASH memory. I make run examples on the DK but on BM832 module can't be possible because...
Hello Nordic Community!
I have seen previous posts mentioning that the DFU example was not working with SDK 15.3 ( Getting started blog ). But in my case I was able to...
Hi all,
I am working on a new project and I need to communicate to a sensor using I2C, then save the data on a flash (files visible on windows as mass storage via USB) and...
Hi,
I am developing an application where the device should support both central and peripheral roles at the same time. My devices are connecting to a mobile phone. All the...
Hi, I use the nRF52840-DK together with a secure element (Infineon Trust X) and want to measure current/powerconsumption of this whole setup during certain operations. At...
Hello!
I'm currently trying to run the mqtt_simple sample (latest version of nrf-zephyr) on the nrf9160 DK. Unfortunately it is not working, because getaddrinfo() returns...
Hi,
I am using the nRF Connect SDK to develop software for a nRF5340_PDK focusing on Security and power efficiency. Therefore I wanted to make use of the CryptoCell-312...
Hello,
The release-notes of the Modem Firmware v1.0.0 for the nRF9160 state that there is now "Support for DNS server address setting by application.". However, I cannot...
After updating to nRF9160 mode firmware v1.1.1 there have been several vector catches. I have not updated Zephyr or anything else from the latest version downloaded on 9/24...
Hi,
I have programmed my Nordic Thingy 91 with lte_ble_gateway and seems to work fine. However whenever I increase the connection parameters, the thingy91 fails in the discoverty...
Hello All,
Please share me the link where I can get complete explanation on software part for how to use following wakeup options as stated in datasheet
1]The detect signal...
Hi all,
I have 3 nRF52840 Bluetooth tags and I have used Segger Embedded Studio for programming the nRF52840 for the proximity application. Once I have programmed all the...
Hi,
We are seeing some strange stuff when trying to pass floating point values to a function. When we pass the parameter by value (meaning as an actual floating point number...
Hi!
I'm trying to communicate with modem through UART.
Power supply: Battery connected to VDDH
VDD_nRF: 1.8V
nRF52840 DK connected to modem devkit using wires (about...
