Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hi ,I use SDK 15.2 ,and example is examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay\pca10040. When I call sd_ble_gattc_primary_services_discover not...
Hi teams,
I am working on Mesh SDK 4.0.0.
I have several server nodes and single client node and all server models are publishing to All-nodes(0xFFFF).
All nodes published...
What exactly are the GPIOTE IN[n] registers?
Is the IN[n] register a function pointer of a function to call when the the input condition occurs on the associated pin? If...
Hi! I'm working on a custom board with the nRF52840 via an SWD connection, from a debug out on an nRF52840 DK.
The debugger fails to connect to one of my boards, even though...
Hi,
I have CSV file stored on an SD card (which I create via the nordic board). I want to send this via a GATT connection.
I have gotten a service with a notifiable characteristic...
Hello,
I have a Thingy91 pca20035 board (not the DK). So far, I have had success building my own modifications of the asset_tracker application by building it using SES...
I can see for the same device on Android nRFconnect that the serial number in advertising data can be seen as here -->
The same device at same time on my iphone X with...
I using nRF52832 with nRF SDK 16.0.
I tested the SPIS example in the SDK.
I want to change the SPI Clock frequency to 8Mhz and read max 255byte at once.
How to set...
Hi
i m using Bmm150 magnetometer sensor. i m trying to read x y z values. However, im not able to obtain the correct magnetometer values. I'm getting 0000 as values in all...
Hi, I'm developing custom board with nrf52832
The problem is that when saadc returns negative value, all values that saadc returns after are max possible values from config...
PLease, could anyone provide me a code exaple on which i can learn how to use sd_flash_write & sd_flash_erease ? I tried to use them but keil give me this : .\_build\nrf51822_xxac...
Hello Dev Zone.
thanks for watching mt ask.
I need help.
I have 2 question.
1. I need use saadc continuous sampling
in SDK example, is it continuous Mode?
...
For RAM locations, I've looked at the getting started guide that discusses using debugging to find the RAM address. https://devzone.nordicsemi.com/nordic/short-range-guides...
I know one of nRF52840 SPI instances supports direct DCX signal drive but I can't seem to find any mention to this feature in nRF52832 so I am assuming none of its instances...
Hi Sir,
As check the ref. schematic of CKAA, the pin count shows 94.
But in the below table shows the pin count is 93
Is there a typo in the datasheet (V1.1)?
...
