Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
I have a time-sensitive block of code run purely by the CPU, not within any interrupt handler or peripheral. Part of the execution is getting interrupted, and so what I would...
I am testing DA7212 with my nrf52840 and i have made connections but i am not sure if thats right. Also i am trying to use i2s loopback example from sdk.
i need some gu...
Hi,
I broke power on/off switch in my nRF52 board. I'm an absolute beginner in hardware (I'm iOS developer...) but I managed to start it. It works, but unfortunately, it...
Hi,
I'm using SDK 13.0.0 and Softdevice s140 5.0.0-2alpha on my nrf52840-PDK. I tested the usbd_hid_generic and usbd_audio examples and they work fine, I can see the device...
Hi,
I am working on one of my application using nRF52840 DK consisting of USB MSC and NUS. In USB MSC example, 8Mbytes of flash is used as mass storage with FAT (FAT12...
Hi, there
I'm tring to use nRF9160 bh1749 example code.
As you know, there is example code about bh1749 in <Install Folder>/nrf/samples/sensor/bh1749.
And there are...
In our product, we use fds_record_write to store some user data on NRF52's internal flash. Is it possible for a hacker to read out the user's data even we have set the read...
Dear Nordic Semiconductor Team,
We are using nRF52832 based module in one of our products. And we are now currently carrying out pre-compliance testing for the product...
Hi
Is Managed Flooding architecture is a Standard ? is it mandatory by SIG.
For example Nordic Stack include -
Messages have a TTL assigned TTL stands for time-to...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0).
I understand that softdevice uses MWU from this document
As per the Errata...
Hello,
I'm a newbie here.
I have a BL652-SA module from Liard Connectivity. It has a nrf52832 with a 32 MHz crystal on board but no 32,768 kHz crystal, so I have to use...
To the kind attention of Nordic support team,
I have been successfully using all gzll routines like in https://devzone.nordicsemi.com/f/nordic-q-a/57839/how-to-prove-to...
Hello-
I am developing my first project with the nRF9160. It is on a custom board. I am planning on using Segger studio with the Segger JLink programmer with the 10-Pin...
I am using nRF52832_xxaa DK and compiling ble_app_eddystone example. I am getting the following error
JLink info: ------------ DLL: V6.54c, compiled Nov 7 2019 17:01:02...
