Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
On my peripheral I filter the devices connected and refuses them when not bonded.
When a device not bonded tries to connect to the peripheral, it forces the disconnection...
Hi,
I am using nrfsdk11 nrf52 and s132 soft device. In my code,I am doing this in main();
void fs_evt_handler(fs_evt_t const * const evt, fs_ret_t result)
{
if (result...
hello sir,
i am using ble mpu example and it working fine now i want do send some commands from mobile to nrf52832 chip via these commands my application should work.
...
Hi everybody,
I will to use the nRF52832 QFAA for a drone, and I carried out this schematic for this chip.
I have two questions :
For the capacitor C6, which value should...
I'm trying to start my app from the bootloader, which is funcionally basically the same as the one in nRF5_SDK_11.0.0_89a8197.
To start the app I call bootloader_app_start...
Hello.
I use nRF52832 and its dev board, S132 soft device. nRF5 SDK v14.2.0 is the version number.
I want to change some manufacture specific data from mobile app. Like...
I am working on the nrf52840 kit with the ble_app_beacon example, compile and download the code successfully. But I don't know how to test whether the kit is advertising,...
I have my own hardware design with the nRF52840 on it. I more or less copied the whole radio/antenna part from the dev kit reference design. The blinky example works fine...
After checking and searching, i found this ble_gatts_conn_cfg_t::hvn_tx_queue_size should be the key to set it. In my custom project (SD132 V5 + SDK14.1) the only setting...
Hi
I'm using IAR Compiler and need to generate some PWM outputs. I tried to use the example code from the pwm_library. But the compiler is generating an Error on the macro...
I am using PCA 10040 development boards with soft device version s132_nrf52_3.0.0 to investigate Central/Peripheral communications.
A PCA 10040 acts as a Central making...
Here is calibration of UART data using ADXL345.
and the data is followed by x, y & z value, for example x = -42, y = 20, z = 268. and then after calibrated 10x which is...
We are upgrading an existing product to use Bluetooth instead of the parallel port.
It must support >20kbit/sec communications between the device and the host PC.
We...
Hey Nordic devzone,
I am tinkering with the following multiprotocol examples:
ble_thread_dyn_mtd_coap_cli (client)
ble_thread_dyn_template (server)
Currently the client...
