Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
I'm running the "Beacon Application for Eval Board" example for the S110 soft device on an nRF51822.
( devzone.nordicsemi.com/.../a00070.html)
I'm using another BLE...
Hi,
I was wondering if it is regual that configuring softdevice for a low frequency oscillator 32.768 kHz using the function:
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
Hi,
Here is output of my chip and i want to read it but there is a problem 25 uS low width (T) is to quick for nRF51822
Can you give me some tips, how to read this 3 signal...
Hello all,
I notice that this library isn't listed in the "SDK Common Libraries" for S210 - is it ok to use this? Internally it does seem to be ANT-aware, even though softdevice_handler_init...
Hi everyone,
I'm using NRF51822 controller for an application, to store 2 float variables in the memory using persistent storage manager feature.
However, when I try...
Hi All,
I try to implement the DFU funtion in my module, but the message return is “Not Supported”.
Please suggest me, how could I do about it?
Thanks.
Vic
...
Hello,
Is there a restriction that I cannot have same address LSByte for radio pipes?
It seems that i am failing to receive data on pipe 0 if for example I have pipe 0...
Hi:
I use SDK7.2.0 encountered a problem when I was disconnected, has reached the maximum number of bonding, I want to remove the first bonding information. I do not know...
when i use sd_ble_gatts_hvx() to send data,it cause a HardFault error。 when i trace the sd_ble_gatts_hvx() function,it will run to 0x00016432,in there will be compare two...
Hi,
I use sd_ble_gattc_write function to write to my peripheral with my central device. I'm sure the settings should be right but i still can't see any change on peripheral...
hi,
i have successfully entered the dfu mode many times and could change the applications and reenter the DFU mode.
But then i tried loading the softdevice at "nRF51_SDK_8...
Hi, All,
I am currently developing with nRF51822AC. Due to some issue, we would like to replace the current 16MHz crystal with a crystal other than this frequency. We would...
softdevice 8.01 s110
device nrf81522
hts example,add three ch adc,lcd eg.
phone : HTC one M7
app:nrf tools HTM
when try to connect the device by BLE, when recive the...
Hello!
I am trying to run example uart project (uart_pca10028) on PCA10028 development board. When code is loaded to the microcontroller it signalizes error - all leds...
