Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
I have put my code developed on a nRF52 dk on a custom board that is based on a ISP1507 CPU. We are having higher current consumption than expected, I use the exact same code...
Hi There,
In company we are working with nRF8001 (currently C revision) and we want to send some custom data in an advertising packet. However, when C revision is selected...
From the S132 5.1.0 specification, I expect that its RAM usage should be only 0x1228 bytes plus ATTR_TAB_SIZE. However, when I compile two of the example projects using IAR...
I am working on a project in Nordic SDK 8.1 that requires using a timer. I am confused where I need to define the timer though (using APP_TIMER_DEF). If I put it right after...
I am working with the SDK 12, nrf52832 low_power_pwm example. I am concerned about the power consumption I am measuring.
I am trying to produce a 1khz PWM for an LED (the...
Howdy,
I am having difficulties writing to NVRAM (reading appears to be fine and is reporting 0xFF's everwhere). I am using a rather old SDK and SoftDevice 110 (version...
How much is the nRF52840 USB DP/DM pins impedance in transmit mode?
There is no info in datasheet .
On the PDK board there are 39 ohm resistors connected in series with...
The engineering B errata mentions PAN 186, that the current consumption in System ON Idle is increased if High-Voltage mode is used. Is there any information available how...
Hi everyone, I'm having troubles with a project using softdevice, and I think it could be a memory problem, I just wanted to confirm that the addresses are correct and there...
Why was this removed? The SD 3.0 docs show only random static and public as options and I get bad address for the others which is consistent with the docs. We were using random...
Hello
Nordic Team.
I controling nrf spi.
testing for example nrfSDK14.0.0\example\peripheral\spi\pca10040\blank\arm5_no_packs\spi_pca10040
/**
* Copyright (c...
Hello everyone, I want to run project ble_uart on NRF52832 in Keil.
At the beginning of the main.c I add
#define BOARD_NRF6310
But get error
C:\Keil_v5\ARM\PACK\NordicSemiconductor...
hi team, i am using nrf52840. is there any hidden services placed in nrf connect app android for gyroscope or we want to create our own services. and also one doubt wat is...
Hi,
I wanted to know the peak current of the nRF51822 chip using the softdevice 130.
I was looking through the documentation and found on the S130_SDS_v2.0.pdf the information...
