I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
With this Main.c, I'm only seeing the 1st 4 bytes of the device name in the NRF Connect app.
Note the use of:
init.advdata.name_type = BLE_ADVDATA_FULL_NAME;
Am I using...
Hello everyone, I added NUS library and I change the sdk_config.h file according to ble_app_uart example. When I built my project, I do not get any errors. But the device...
Hi support team,
In order to make the application hex valid after programming in a bootloader enabled project, we can use bootloader-settings.
As for secure DFU, it...
We are upgrading some products to SDK 14.2 and creating some new ones.
We need to start production programming of boards. I can't find the information on how to do this...
What is the maximum and minimum frequency of the PWM signal/square wave that can be measured on the NRF 52DK board I'm using NRF 52832.
Also, what is the max and min "pulse...
Hello,
I have found similar questions on transmitting multiple bytes over SPI, but I am still not sure how to do it. I want to communicate with a driver which needs to be...
Hi,
I found the 'Solar Sensor Beacon' example from
https://github.com/NordicPlayground/solar_sensor_beacon .
There, I found that no softdevice initialisation (nrf_sdh_ble_enable...
I am working through the nordic sdk 8.1 peripheral heart rate monitor example. I am wondering what RR is? I can't figure out what it stands for or what the purpose of it is...
Hi,
In my current project I have indicating LEDs connected via TWI bus. In this case, I can't use BSP_LED_0/BSP_LED_1 outputs to indicate states as it implemented in nrf_ble_dfu...
Hello, I recently use nrf52832 to make a wireless sensor network of BLE concurrently with NRF_ESB.
During development, I use only 2 sensor. Both sensors are connected to...
ANT S212, nRF52:
I've read all the links in the forum regarding serial port running in debug mode and not in run mode.
In my case, it works in RUN mode until softdevice_setup...
Hi
I have a sensor array which data have to be advanced burst to one or many devices.
The array size is anything from 24 bytes to 24k bytes, depending on the number of...
Hi guys,
I am using nrf51822 and SDK 11. I have some trouble about suddenly reset the nrf51822.
In my application, I used uart_fifo to received some information from other...
