I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
I have a need for an interrupt to go off at a 4khz rate. For this, I am using a repeated App Timer (running off the 32k crystal).
Prior to adding this extra timer, we used...
I'd like to run the DK in at the lowest power in SYSTEM_ON mode.
It's my understanding that the ble_app_gzll example places the system in the "low power" SYSTEM_ON mode...
Hello Folks
I would highly apprciate if anyone can point me in the right direction here
After lot of consultation we imported a smal size shipment (of about 1000 nRF51822...
Connection_mode_with_1sec_Notification.jpg
In my BLE project I am using connected mode, and I found that the current consumption is very high ~190uA during idle mode. I...
I'm currently working with an own hardware with a nRF52840. We had some time to get the radio working, because we copied the schematic of the PDK. In the reference design...
Hello I am using sdk version 14.0 and softdevice S332. I am looking at the ANT + bsc code. I have two questions when looking at this code.
bsc_tx could not see an event...
Hello guys,
Please help me on this.
I want to erase BMD 350 chip using BMD 300 erase and recovery software tool. But I can not do it.Error comes as per the attachment...
Dear all,
I want to create a star network, composed by one gateway and a limited number of nodes. The nodes periodically send information to the gateway. I am using the...
I'm running the HID Keyboard example from SDK 12.2.0 on nRF51-DK with SD 130.
When I long push Button1, it disconnects for a moment and connects again immediately.
Events...
I am trying to make a custom application in which I need to connect to a device and read/write its characteristics' value.
But my target device has had 4 primary services...
Hi Nordic Engineers!
we bought 110 nRF52840 IC's for Field tests.
10 of them marked Q1AAAA / 1716AK
another 100 marked Q1AABB / 1745AC
What is difference between series...
Dear Nordic Team,
Thanks for supporting.
Now i am work with secure dfu using SDK12.3.0.
My Hardware :PCA10028
nrfutil version 3.1.0
Create Zip file like : nrfutil...
Hello.
I want to design a product. It will have these features;
It has 4 buttons on it.
Obviously it is battery powered device.
I want to see some information...
Hi
I have made ble scanner using nrf52 and I have set uart baud rate 921600 and sending scanned beacon to other micro-controller for processing but It does not scanning...
