I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I want to change type from "uint32_t val1 = 0xAA01" to "uint8_t val2 = {"AA01"}.
Then, attr_char_value.p_value = val2;
=> sd_ble_gatts_characteristic_add(p_rms->service_handle...
I am currently trying to develop Mesh applications using the Nordic Mesh SDK and the nRF52840 Dev kit. The problem that I am having is that my testing equipment isn't able...
We have a custom hardware device that uses the nRF51 and the S130 softdevices. We are able to connect our device to our app on iOS and Android and through a web-bluetooth...
I want to erase selected pages from the NRFflash memory (Not whole flash).
I have defined one function for NRF memory erase. In that, I have followed following sequence...
Hello, i am using NRF 52832 QFAA
In pstorage_platform.h I see
#define PSTORAGE_FLASH_PAGE_SIZE pstorage_flash_page_size()
and the return value of pstorage_flash_page_size...
Hi Nordic,
I have been quiet for a long time but here is another question.
For the project I am working on I want to measure the current with the PPK. Although it seems...
Hello. When I received nRF52DK, I have successfully uploaded some examples also with softdevice through the Keil IDE. But after few days Keil and also Segger IDE stopped detect...
Hi. I'm new to both the nRF24L01+ and to this forum.
I'm intrigued by the prospect of using these amazing little transceivers as RF modems. Because I find elements of the...
Hi,
On SDK12.2, I replaced main.c in ble_app_template with one in twi_scanner and modified sdk_config.h.
But, no expected log, even "TWI scanner.", issued to terminal...
Hi,
I want to add a service to the "ble_app_beacon example" that i can change
the value of the major and minor directly via nrf connect, some one can help me
to add the...
If I leave the CE pin in a HI state, and assuming I have the PWR_UP = 1 and have loaded the Tx FIFO with data, will the data be transmitted by merely setting PRIM_RX to a...
I've paired ble device with android and then device went out of range and wen ble device comes into range device will connect at that time do we get any callBack???
Hi,
I'm looking at increasing the sensor update rates for the Thingy:52, and get more frequent readings into the sample app. Let's assume I want to change the temperature...
