I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I had successfully write a structure data to fds. After which, I would like to update the same file and record key with new values of a structure. After updating, I will read...
Imagine I have developed a MESH made up of 50 Relay Nodes and I say only Relay Nodes because any of them must be able to relay and also able to initiate a message. In my application...
Hi,
I am making a GPS tracking system using NRF51822-QFAC. I am using 2 UARTs, one of the (external) GPRS IC and one for (external) RS485 communication.
The UART peripheral...
HI,
I tried to compile Thingy v2.1.0 with keil. And sereval file are missing.
Actually i work with your SDK 14.0.0, i find so many missing file, but not all.
Can...
Hi,
I am currently testing with a USB MSC example .
FATFS_QSPI is disabled because the file system is not used,
Subclass has also been modified to 0x06 -> 0xFF.
...
Hi,
I am implementing experimental_bootloader_secure_usb code example on PDK PCA10056 V0.9.2 using Sdk v14.0 and also tested with Sdk v14.2 but in both cases Windows 10...
With SD140 v6.0.0.6 having been released, will an accompanying example project that demonstrates simultaneous use of BLE and USB be released? Will this be included in the...
Dear devzone,
I am currently merging the Mesh SDK into the normal SDK to run BLE & BL mesh concurrently.
Followed multiple guides to get it working, at this moment I am...
I use nrf52832 development kit,nRF5 SDK for homekit.
Now I have read and write to UUID, want to realize how to handle the notification operation, and call what API?What are...
I enter to bootloader via my app by UART command:
err_code = sd_power_gpregret_clr(0, 0xffffffff);
APP_ERROR_CHECK(err_code);
err_code = sd_power_gpregret_set(0, 0xB1...
I know nothing about bluetooth
like ble_app_uart , uart to where?how to use this uart?
like ble_app_alert_notification, alert? beep? vibrator?
any tutorial of develop...
Hi. I am connecting to and establishing a bond between my Android phone and the nRF52832 board using the s132 SoftDevice. I'm in a situation where the Android phone has a...
Hello,
I have the following setup:
A Raspberry Pi 3 B and a nRF52840 Development Kit acting as a Border Router as described here
Another nRF52840 Development Kit...
Hi there,
I'm trying to run the beacon s130 pca20006 example on a custom board. There are 2 main differences between the pca20006 and my board:
There is a 32 Mhz...
Hi,
it seems there was lately a new IC revision release of the nRF52840.
Is the nRF52840 IC Revision Engineering B 100% pin compatible to Engineering A, i.e. pinning...
